After sanding the boards, the router table was set up with a dish cutter bit and some timber clamped to the table to act as limiting stops. The end of the boards were then passed over the bit to create the recesses… This was done in several passes.. raising the bit after each pass. There is a little burn mark on the ends but a lot of sanding will remove this… lol Nah… I can live with a little burn… it will blend in ok with some oil… As you can see ...
I have an end grain cutting board made of purple heart and yellow heart. The blocks are squares, 1-1/8” square, about 1-1/2” long/thick, glued up with mixed patterns (making letters). The board was treated with mineral oil. It appears that the yellow heart pieces have swollen from absorbing the mineral oil, and have busting some of the glue joints. Has anyone ever experienced this type of problem? Thanks for reading and your comments. Kevin
Yesterday I was a little busy…. I ripped and glued up some blanks for some boards…no pics but they were just simple laminations… Today when the glue was set I took them out of the clamps and made the secondary cuts and got ready for the next glue up… Here are a few Camphor Laurel end grain boards.. Not glued up yet.. A smaller version to go as a pair… maybe… Can’t wait for the glue up… and sanding… then a coat of oil to pop...
My shop group ( Retired folk) was donated many short cut offs of ipe, epe..Can they be used for making cutting boards? I know this stuff is hard and hard on tools…is it hard on people who use them?should we just throw it away or make something useful?Comments and suggestions appreciated.
Oak leaves have a unique and distinctive leaf shape Oak trees grow on each of the five continents and cultures at every level have relied on the wood and acorn, the tannic acid and the bark throughout the millennia. Great ships with oak bows and rudders crisscrossed the globe. Massive barns and manorial homes came from the stems and crooks of full-grown oaks in every county. It would be impossible to catalogue the provision we have from the ancestry of the common oak. Oak works...
Lots of great info on this blog! Hoping to get a little guidance here. I am new to woodworking after finding a stash of rough walnut in my Grandfather’s garage after he passed. At this point, all I want to do is build some end grain cutting boards as many of you have done. I have a planer, dust collector and jointer from cragslist that do a great job. All I need is a the table saw. I have very little invested in this and don’t want to spend a lot on table saw as there is a c...
Several years ago I saw this ribbon design at segmenting.biz/inlayexample. I started by selecting the body of the design. In this case, padauk, yellow heart, aand hickory for three boards. Then I laminated the “ribbons” Then I cut 2” holes in the boards that make up the body of the design. The problem for a flat boarder(cutting board) was how to create the plugs without a center hole. The first idea was wood turning but this would require a massive square of exotic wood...
Gidday all, Many of you have made cutting boards and many more are going to make cutting boards. This is in itself very good but like Marc Spagnoulo how many have wondered how the ones you made a while ago have faired.,I made my first board over 4 years ago and it is still going strong and just about due for a little refurbishing,.lol’My first ‘butcher block end grain’ board is still being used daily and also just about due for the quick sand and re-oiling. Just thought I pu...
I figured it’s time to start my blog on Lumberjocks, and what better way than to announce that I’ve started an Etsy store for my woodwork (so far just cutting boards, but more to follow) and my wife’s mosaics! If you want to take a look, it’s here:https://www.etsy.com/shop/GMosaicsAndWood?ref=hdr_shop_menu Regards,Patrick
It’s been a long haul and not without a few setbacks, but our first semi-production run is almost complete. I have to say (and I have seen this mentioned before) these tops are the most labor intensive project I have ever experienced. With that said, I still have to build 3 more. It’s official-I really am not that bright!! and Cherry Base Clear Coated Tiger Maple and Walnut Base with Cherry Top That Big chunk of Maple with the pine “CA-ed” to the edg...
- My Journey As A Creative Designer - Woodworking and Beyond - 1742 parts
- Extremely Average - 324 parts
- Workshop Development - 107 parts
- A journey into the workshop. - 105 parts
- Just for Fun... - 97 parts
- Daily Update - 87 parts
- Life as an Amateur Woodworker - 79 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 76 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- Sheila Landry (scrollgirl) - 1767 entries
- dbhost - 418 entries
- frank - 417 entries
- degoose - 397 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- mafe - 304 entries
- Martin Sojka - 296 entries
- William - 258 entries
- shipwright - 245 entries
- Betsy - 228 entries
- stefang - 220 entries
- robscastle - 218 entries
- Dave Rutan - 213 entries
- Stevinmarin - 212 entries
- Todd A. Clippinger - 207 entries
- Gary Fixler - 204 entries
- Smitty_Cabinetshop - 193 entries
- A Slice of Wood Workshop - 190 entries