Update 2-19-2009: For photos of the restored Maillard Conformateur & Formillon For photos showing another restored Maillard Formillon here And photos of a Carrying Case for the Maillard Allie Conformateur and Formillon - – - – - – - – - – - – - – - – - – - – - – - – - – - – - – - – - – - ——sorry photos aren’t loading, I’m working on repairing this...
I saw this FWW Complete Illustrator Guide to Woodworking, and while I found most of the book to be mediocre (although a nice reference book when you’re starting woodworking) I did pick up a couple of cool ideas from it… then again, it might have been from a different book…lol so I finally mounted my (until now just laying there) hand planes in the cabinet. The shelves are shaped to the profile of each handplane for full support, the shelf has a small ‘step’ (1...
After some success with pens and a few bottle stoppers, I decided a bowl was overdue. I picked up a couple 2×6 rounds last week of curly maple and decided to see what kind of bowl I could fashion from one. I located center and attached the faceplate with some screws. My intention was to cut the bottom of the bowl for the Nova Chuck and shape it as much I could before turning it around and hollowing out the inside. I made the recess and shape the outside curve then sanded it to 600 grit. ...
I bought a No. 45, but the cutters did not come with the boxes that were included at the original purchase, all those decades ago. Not wanting to spend a large amount of money for real boxes, I’ve opted to make my own reproductions. However, I wanted them to be as close to the original versions as possible. The astute reader will note that the No. 45 cutter boxes had graphics on them displaying the contents of each box. These tend to get destroyed over time and are very rare to be...
This is a short blog, I hope, to show some work I was able to get built this week in the shop for a commissioned project. - – - – - – - – - – - – - – - – - – - – - – - – - – - – - – - – - – - – - – - – - – - - This tool is a Rounding Jack used to trim the brims of hats, and will be used by a discerning hat maker. In this exciting development, I have comp...
Ok, when I last left you this cutting board was just a Sketchup design. After a trip to the hard wood dealer and some basic milling I arrived at this very hefty glue up. I tried to do the ripping on my BOSCH, but even with a thin kerf blade it was a little too much for that saw, so I took over my buddies cabinet shop! Here are some shots of the first glue up..Here is the blank, out of the clamps and sanded to 1 1/2” thick..Ok, now the fun part..After squaring one end up on the radial ar...
I have wanted one of these for quite a while and last week the gods of eBay smiled upon me. The beader is essentially a mass produced scratch stock that puts profiles on wood. Stanley made them from 1886 to 1941. Because this one is jappaned, it was made before 1898. Handplane Central has some information here. When shopping for them you want to look for one that preferably has its fence and set of 9 cutters. You can also make your own cutters with custom profiles. Both Lee Valle...
I designed a log clamp to hold logs that are too big for the lathe. My friend, Mitchel Dillman over at Colorado Rock*N Logs fabricated it for me. See how to use it to carve a tenon in this video! Please visit my website and FaceBook Page. Thanks!
After having to cut all the tenons by hand on my shaving horse i decided I never want to do that again and when i got paid for a quick welding job I picked these up for $65 including shipping. As far as the age and manufacturer of these tools i have no clue all I can tell is they are most likely cast iron. Here are some photos of them after I spent a couple hours cleaning them up and getting all the stubborn screws free again: I’m half tempted to replace the machine screws ...
I had been saving a nice Honduran rosewood cut-off for a while before the last weekend. I wanted to make a marking gauge and thought rosewood was a good wood for it: dense and oily. A few gauges seen at LJ and in several ww magazines were an inspiration. The planned dimensions: fence—2-7/8” × 4-1/2” × 7/8”, beam—3/4” × 1” × 9-1/2”. Cut the beam and fence parts; got a 1/8” × 1” brass bar for wear strips from a recycled construc...
- My Journey As A Scroll Saw Pattern Designer - 1597 parts
- Extremely Average - 324 parts
- Workshop Development - 107 parts
- Just for Fun... - 96 parts
- A journey into the workshop. - 89 parts
- Daily Update - 87 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 76 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- ScrollSaw Information and Resources - 68 parts
- Sheila Landry (scrollgirl) - 1622 entries
- frank - 417 entries
- degoose - 397 entries
- dbhost - 390 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- Martin Sojka - 296 entries
- mafe - 279 entries
- William - 258 entries
- Betsy - 221 entries
- shipwright - 218 entries
- Stevinmarin - 212 entries
- Gary Fixler - 204 entries
- Todd A. Clippinger - 199 entries
- stefang - 198 entries
- Rustic - 188 entries
- BritBoxmaker - 187 entries
- Chris Davis - 183 entries
- Smitty_Cabinetshop - 176 entries