LumberJocks

Woodworking blog entries tagged with 'craftsman'

  • Advertise with us
View toolmike's profile

Rhykenology #4: Cloned planes (Part 2)

12-12-2013 02:35 AM by toolmike | 0 comments »

This is the second part of a series on cloned block planes. It looks at Craftsman, Dunlop and Fulton planes. http://workingbyhand.wordpress.com/2013/12/11/the-clone-wars-part-ii/

Read this entry »


View pintodeluxe's profile

Caden's Library Chair #1: Glueup and Dye

04-18-2013 11:54 PM by pintodeluxe | 0 comments »

The seat rails are notched as they intersect in the rear legs.-----Backrest glueup…-----Parts waiting to be assembled.-----Front leg assembly glued up. ----- Seat rail glueup.-----Wiping on the Transtint brown mohogany dye makes the white oak pop. Next up will be stain, lacquer, and leather upholstery.

Read this entry »


View Rapola's profile

Unisaw Restoration #3: Is 4 tables saws too many?

05-28-2016 03:23 PM by Rapola | 0 comments »

I made some decent progress on the unisaw. With the exception of the yoke/motor bracket assembly, all of the base components are disassembled and I have started stripping the old paint off the cabinet. Hopefully I’ll finish out this long weekend with most of the parts cleaned and primed for final paint. There is a tapered pin holding the yoke/motor bracket together that has thus far thwarted all reasonable attempts with PB blaster and heat. In reading various forums, it seems the ...

Read this entry »


View ontheworkbench's profile

On the Workbench #4: Adventures with a Craftsman Midi Lathe

01-04-2015 09:52 PM by ontheworkbench | 0 comments »

I found a Craftsman Midi Lathe (#21752) for an unbeatable deal, and combined with coupons and SYWR points, it was just over $100 (list price $450). But for that price it came with a few problems. I first found it listed on Sears Outlet, and then when I went to the mall store locations, I had to do some asking to get. Upon inspection I discovered that the belt cover was cracked, not much, but just a little. and everything else looked great. The manager suggested that I purchased the protection...

Read this entry »


View pintodeluxe's profile

Mission Dining Build #4 - The Table

11-17-2011 08:01 PM by pintodeluxe | 0 comments »

The dining table is well underway, with the frame assembled and equilizer slides installed. I think there are some misconceptions about equilizer slides. They work for pedastal tables, or any design where the legs are stationary when opening the table. I had to do some searching to find slides that would accomodate this 46” wide by 104” long table. It will have two 12” leaves, and is 80” long when closed. The other spec I needed was...

Read this entry »


View CaptainSkully's profile

Arts & Crafts Dining Room Set #1: Test Drive

07-03-2009 07:15 PM by CaptainSkully | 0 comments »

The first installment of this blog is here due to LJ blogging technical issues… To make sure the dimensions are correct for our new table, we decided to do a little test drive. It didn’t hurt that we’re having eight people over for a Fourth of July BBQ. We ran over to the big box store and bought a sheet of particle board for $29. When we got it home, I cut it down to 45” x 72”, the finished dimensions of the table top. After I sanded it and eased the edge...

Read this entry »


View Douglas's profile

Blogging instead of Woodworking #8: What a Waste

08-15-2014 12:49 PM by Douglas | 0 comments »

Over on my blog, I’ve been catching up on some of the things I’ve been doing for the last several months. One is a set of wastepaper baskets, a few different designs, I made from cutoffs & scraps. I dip my toe into the “what to do with scraps” debate, and a few other things. Enjoy… http://dcwwoodworks.com/blog/2014/8/12/what-a-waste

Read this entry »


View withheld's profile

A workshop out of the floodplane #3: A new fence for the old saw

01-19-2011 05:20 PM by withheld | 0 comments »

Based on Jamie's blog entries on upgrading a Craftsman table saw with a new delta T2 fence, I decided to do the same.The fence arrived last night I might need some better drill bits for the job and a good center punch, if I understand his blog entries, but it sounds like the thing to do is proceed very slowly and carefully. Which in my case means measure 10 times, cut once. As an aside the thing the fence is resting on is a small pegboard tool holder I started working on. Given my skill...

Read this entry »


View HuckD's profile

Videos by HuckD #18: Dowel Jig 3

01-27-2016 07:20 AM by HuckD | 0 comments »

My third dowel jig. This one for edge joining boards for table top glue ups. Simple, inexpensive and easy to make. https://youtu.be/MLMpO8BQfFk

Read this entry »


View Douglas's profile

Blogging instead of Woodworking #20: At Last, a Morris Chair, Part 1

06-21-2016 04:10 PM by Douglas | 0 comments »

I just blogged (with lots of photos) about the Morris Chair I built this past spring. This part 1 goes through most of the build, and part 2 will be finishing, upholstery and stuff. For LJs, I’m also posting a project here too. http://dcwwoodworks.com/blog/2016/6/14/at-last-a-morris-chair (link fixed!) Here’s a few pictures…

Read this entry »


« prev 1 ... 18 19 20 21 22 next »
213 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com