I waxed the dressers with Howards Walnut wax and #0000 steel wool. I tested the difference between sanding with a 1500 grit sanding sponge, and waxing with steel wool – and I prefered the latter. I waxed with the grain, and let the wax dry. Then I buffed it off with a clean lint-free rag. ----- For drawer pull layout I used Scott Collins no-math layout method. My drawer pulls have 2 bolts, 3” on center. -----I made a full-height jig to drill the holes for the machine bo...
With a stack of drawers ready to go, I turn my attention to applying the finish to the carcase.-----Oil based stain was applied to the carcases and drawer fronts. I sprayed the carcases, and wiped stain on the drawer fronts. -----Then I sprayed two coats of lacquer, scuff sanding between coats. ----- Next I install the Centerline full extension drawer slides. Having web frames is convienent, and I simply set the slides down on the web frames. -----I use a jig to align the slides. ...
Here is my setup for cutting half blind dovetails. I use a larger-than-stock 14 degree dovetail bit. I think it makes nicer looking dovetail joints, and they feel much stronger. Here is a link to my blog about the special bit… http://lumberjocks.com/topics/40073-----This is the bit I use, which is a Rockler item. You can still cut these dovetails in one pass with the PC jig. -----I trimmed some aromatic cedar plywood to size and test fit the drawers.-----Grooves were cut for the dra...
With the top built, it was time to turn my attention to the backsplash inlay and wedge detail. ----I cut a double sided taper on the backsplash piece using a tapering jig at the tablesaw. ----I saved my offcuts to make wedge shapes. The wedges were glued back onto the backsplash. I was careful to place the wedge in its original position so the grain would align. ---- The backsplash is carpet taped to a strip of MDF. This creates a straight reference point to cut shallow dados for m...
Here is the plan from my design. It incorporates some Stickley design elements. --The dresser carcases are assembled, including the small divider that separates the top two drawers.--The small dividers are attached with biscuits. To cut the slots, I opened the top two web frames like a clamshell. The web frames were aligned, and clamped together. Then I added an Emerson straightedge clamp, positioned to center the small divider on the web frame. --The ruler on the Emerson clamp helps cen...
It is now time to build the web frames that function as drawer dividers. The web frames are notched around the legs, and I decided to cut the notches with a dado blade. Here is my setup at the tablesaw with sacrificial fences on both the tablesaw and miter gauge. The result was nice crisp corners on the notches. This will be a visible joint at the front of the dresser. A bandsaw could also accomplish the task, but not quite as easily as a dado blade. After cutting pieces to ...
I cut the plywood backs to size, and checked the fit. Shiplap backs are nice when they are visible, however the strength of plywood is undeniable. The plywood back fits into a rabbet in the rear leg. The side panels feature floating panels. They are glued only at the center to allow some wood movement. While gluing the side panels, I centered the wood panel for an even reveal on all sides. I cut 1/4” deep dados into the 1/2” plywood back. These dados will lo...
If I have more that 2 parts to shape, I will make a template out of mdf. I prefer a nice solid jig made from 3/4” mdf with toggle clamps, however since I only had 4 lower side rails to make I kept it simple. After rough cutting the curve at the bandsaw, I used a 1/4” thick template carpet-taped to my workpiece. A pattern bit mounted in the router table makes quick work of cutting the gentle curves. I try to rout “downhill” on curved pieces. In other words,...
I spent some time card scraping and sanding the 1/2” thick panels for the dresser sides. I sharpened a fresh burr on the card scraper so it was cutting quickly. I use it on trouble spots, like tearout from the planer. I setup the tablesaw with a dado set and a sacrificial fence to cut the rabbets on the panels. They are rabbeted on the inside edge, which will produce a flat panel look on the outside of the dresser. I could have used plywood, but it can be tough to find quartersawn ...
I started the dresser like I start most of my projects, by laminating up some legs. I am making two dressers, so 8 legs were in order. I cut strips of 3/4” quartersawn red oak, and resawed a few of them. I could then glue 3 pieces together to get my leg width. Finally, I glued on 1/4” thick stock to cover my jointlines. After the glue dries, I plane the thickness of these veneers to about 3/32”. That way, I get quartersawn grain on all 4 sides. I then milled s...
- My Journey As A Creative Designer - Woodworking and Beyond - 1768 parts
- Extremely Average - 324 parts
- A journey into the workshop. - 109 parts
- Workshop Development - 107 parts
- Just for Fun... - 97 parts
- Toy costruction - 93 parts
- Daily Update - 87 parts
- Life as an Amateur Woodworker - 80 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 76 parts
- Sheila Landry (scrollgirl) - 1793 entries
- dbhost - 430 entries
- frank - 417 entries
- degoose - 397 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- mafe - 304 entries
- Martin Sojka - 296 entries
- William - 258 entries
- shipwright - 253 entries
- Betsy - 228 entries
- robscastle - 226 entries
- stefang - 221 entries
- Dave Rutan - 219 entries
- Stevinmarin - 212 entries
- Todd A. Clippinger - 207 entries
- Gary Fixler - 204 entries
- A Slice of Wood Workshop - 199 entries
- Smitty_Cabinetshop - 194 entries