So here it is, the final glue up. I over clamped to be safe, not in the sense of clamping pressure but as far as where I was clamping. This glue up entailed gluing all 4 sets of tails and pins with the mitered front (all the same piece) of the carcass as well as gluing in the center of the floating panel. By glueing the center of the panel I control the movement of expansion and contraction to both edges, ensuring the gaps always stay very close to the same, also keeping them as smal...
When working on my various woodworking projects I found times that I had to glue odd joints and really didn’t have the clamps I needed. The solution to the problem was the development of a clamping block that simplified clamping these uncommon joints. The Universal Clamping Block tool will let you clamp the usual miters and and frames but will also facilitate the clamping of a great variety of other joints that occur in woodworking projects that present special clamping problems. ...
Used tools: Often a great bargain, occasionally a spectacular bargain, sometimes a puzzle, rarely but delightfully a chance to acquire something with soul and a story to go along with it. Clamps are certainly about the least glamorous of all our toys, er, tools. But you can’t have enough, as the adage goes, and because they don’t make noise or sawdust or plug in, they don’t have much emotional draw. I’ve managed to bridge that and make it a passion to find an...
Hey guys. Just fooling around tonight. Found this Clamp here on Lumberjocks. Thought I’d make a Google Sketchup file for it. Anyone need any Google Sketchup Designs just let me know and I’ll see if I can help you! (if you want the file for this clamp, just PM me and I’ll send it to you through email) Make sure to check out the other blogs in this series – if there are any templates you can’t seem to figure out how to draw (on the compu...
... with a little luck….with a little luck…..and some help from my sister, handtools ..... I have over the year always talked about how great and fantastic possibillity it is for you to have acces to fleamarkets and other places where it is possible to buy good used beautyfull handtoolsmore or less rusty but with a little albowe grease and knowledge is going to bee great users again I have envy you alot when I have seen your toolgloats witch has cost mee many green bulbs and...
My mother suggested that I make a picture frame for my grandmother’s 100th birthday. The party is in march, and the four of us (Stephanie, Beatrice, Elijah, and I) will be flying to New York. I looked online for table saw frames because I do not have much skil with or many bits for a router, and no router table. What I found was: http://americanwoodworker.com/blogs/projects/archive/2009/12/04/tablesaw-picture-frame.aspx This is a lovely and classic frame. The wood is beaut...
We are now ready to begin sawing out our components. By hot gluing the two boards together this allows us to cut two identical pieces of each part so that they will fit properly. Note that I am only sawing out the interior shapes of the cross at this point. This will allow me to have better control when re-gluing. Here the vertical piece has been cut out. Keep in mind that you must get the best cut possible. Be sure your blade is narrow enough that it can saw the curves without backing up ...
I have undertaken my first solo project without having someone around watching that knows more about making stuff than me – the garage was empty except for me. My wife had requested, about 1 year ago, that I make this bench for the hallway leading to the laundry room that would be a place where we can sit, take off our shoes and have a place to store them. Since I was slow to act, she bought a wicker basket that shoes get thrown in. Finally, I started on this project over Labor day week...
Here is another great use for the Torque Work Centre. I am frequently needing to slot pieces for various jigs I have built. Up until now I have been using the router sled I posted some time ago. That worked very well, and was safe to use, even on small parts. The Torque Work Centre does the same thing, but the set up and ease of use is much better and faster. Here I’m slotting pieces for wooden clamps like these I posted recently as a project.This is the set up for the flip stops to ...
- My Journey As A Scroll Saw Pattern Designer - 1387 parts
- Extremely Average - 324 parts
- Workshop Development - 107 parts
- A journey into the workshop. - 89 parts
- Daily Update - 87 parts
- Just for Fun... - 84 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 76 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- The Craftsman's Path - 67 parts
- Sheila Landry (scrollgirl) - 1410 entries
- frank - 417 entries
- degoose - 394 entries
- dbhost - 389 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- Martin Sojka - 296 entries
- William - 258 entries
- mafe - 229 entries
- Betsy - 221 entries
- Stevinmarin - 212 entries
- Gary Fixler - 204 entries
- Todd A. Clippinger - 193 entries
- Rustic - 185 entries
- Chris Davis - 183 entries
- shipwright - 180 entries
- BritBoxmaker - 166 entries
- stefang - 164 entries
- PurpLev - 163 entries