LumberJocks

Woodworking blog entries tagged with 'clamp'

  • Advertise with us
View Retsof's profile

Outdoor Furniture #11: Patio Planter Boxes - Continued

06-17-2012 05:23 PM by Retsof | 0 comments »

I’ve made a lot of progress on this project, but I’ve been so busy since the kids got out of school for the summer, that I haven’t had much computer time lately to update my blog. Here I have the three piece legs glued up and I’m testing the fit of the tenons. In this photo, I’ve finished the sanding all the parts, have the tenons glued into the legs, and have the panels installed. Now they are starting to look like planters. One of the changes I ma...

Read this entry »


View Mark Kornell's profile

A Sliding Door #6: On the glue

11-08-2014 01:41 AM by Mark Kornell | 4 comments »

Started the glue-up yesterday, finished it today. Yesterday: I started by checking the fit for all the pieces. First up, the panels. And they don’t fit, which was expected. The groove has round ends while the panel is square: A few ways to fix this, but I picked up the mortise chisel and mallet to square off the ends of the grooves. The panels fit now The panel was a pretty tight fit, but I can address that later. Glued tenons into the first rail And then the rail into...

Read this entry »


View bandit571's profile

Maple Chest of Drawers #8: Another glue up, and some web frames

08-03-2017 07:14 PM by bandit571 | 1 comment »

Ok, this one will be a long-winded one….I managed to get the second side all glued up.. Took the clamps off this morning,,,,might need them later.Set up a saw on the bench.. As I needed a few parts cut up, to make web-frames… Extra hand to hold while I saw. Needed 10 pieces @ 3/4×2 x 24” ( the 2” is about 1-1/2”) Set these aside, needed 10 pc. @ 11-1/4” long, and a a bunch of 3/4×3/4 kicker stock.. These two were fine as is.. ...

Read this entry »


View Darryl Jones's profile

Dread Knot Woodshop #2: Build a clamp rack

10-13-2015 12:15 PM by Darryl Jones | 2 comments »

https://youtu.be/9xRjNLqAnF4 In this video I show you how I built a clamp rack to organize my parallel clamps.

Read this entry »


View bandit571's profile

What to do with a Walnut slab.. #3: Last of the saw work, start of the cussing

11-27-2015 10:42 PM by bandit571 | 2 comments »

Well, Landlord WAS coming over to finish the painting upstars…..fell asleep. he will TRY to get over here in the morning….he says. Wandered down to the shop, to see what sort of trouble I could get into…. Had three parts to make tenons on….two had curved sides. Might be a bit tricky to clamp in the end vise? I picked out a scrap of walnut from when I sawed the curved parts. Had to trim the ends back a bit.. So I could clear the “work area”...

Read this entry »


View PhilBello's profile

Life as an Amateur Woodworker #69: Towel Rack

01-26-2016 01:04 AM by PhilBello | 6 comments »

The weather here in Colombia is such that, even when it is winter it remains at least warm, we have no heating, and drying clothes, bedding etc. is no problem, we have a covered drying area outside, but after a shower, my towel until now, has been draped over anything available upstairs, where it has dried but looked unsightly, it was time to do something about it. I pondered on design, as I had some 1”dowel and plywood, but in the end went with trusty 2×4!! For the first time I...

Read this entry »


View bandit571's profile

Shop storage projects #21: Need a dresser for chisels, starting up

02-13-2017 03:40 AM by bandit571 | 1 comment »

Main dresser is done, and almost loaded up. A drawer I had found on the curb during Trash Day provides the start for the next little project. I had that old box of chisels, that needed a better place to hang out in.. This is the drawer I found. I separated the chisels into two groups. The Plastic handle crowd was laid out in the drawer, and some scrap pine was added as dividers.. I’ll finish nailing the dividers in place later. There is a place to stash a small chest of...

Read this entry »


View Esko Lehtovaara's profile

New home for the horses #2: The End. Finaly.

09-24-2013 10:14 AM by Esko Lehtovaara | 0 comments »

It’s now 24.9. It all started on 26.8. (with renting a sement mixer. It took only 6 hours for us to get the slab done.) Since then allmost every day has been a workday. Maby 3 days has been lazy day with only 2-3hours of work. Still. I started to be quite fedup. Rest of the work is a piece of cake: digging a ditch for the rain water. I’ll put a tube on the bottom and fill with gravel 008. The “door” from the old ‘pihatto’. Pihatto is the house for the hors...

Read this entry »


View Dave Rutan's profile

Shopmade Luthier Tools #20: Neck Clamps for Violin, Cello, etc...

04-03-2017 05:09 PM by Dave Rutan | 5 comments »

There are at least two instruments in the shop that need necks reattached. I was shown how to do this when the entire neck is detached, but two cellos are broken at the joint and the method shown me might not work so well. Google to the rescue! I found photos of commercially available models, selling for multiple tens of dollars, and decided I could make my own. I used some of the mahogany at my disposal, some 3/8 in. threaded rod, and some sheet cork I was given a few years ago. ...

Read this entry »


View bandit571's profile

End Table project #3: Frame and panel work

07-26-2015 02:36 AM by bandit571 | 1 comment »

Well, last time, I had a couple frames almost done. I went down to the shop a couple times today. Got the second large frame all joinered up. Then worked on the narrow end frame.. This is from laying out where the rails would go. First I had to trim them to length. Got out a mitresaw.. A little old school, but it works. Had a plain candle handy, and before most cuts, I’d rub the saw with the candle. Made sawing thos oak a breeze. Cut a few tenons with that same saw. h...

Read this entry »


« prev 1 ... 46 47 48 49 50 51 52 ... 102 next »
1014 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com