Enjoy these top woodworking tips. Increase your woodworking skills. If you are new to woodworking or an intermediate woodworker, I encourage you to study this video and article time and time again. There are a lot of basic and advanced woodworking techniques used in this process that will help to drive your woodworking skills to a higher level. How to Make a Picture Frame - Top Woodworking Tips The above link will provide you with detailed woodworking information relating to the Top ...
Drill Press Station – Table/Lift/Fence/Vise/Drum Sander My drill press is a small inexpensive bench top type, and until I get a good floor type one I am trying to get the best out of it. One of the first things I did was to change its old pole with a stainless steel one. Why stainless steel? Well it was the only piece I could find that matched the diameter and you can slide up and down smoother. So the pole got a lift-up of about a foot taller. One of those ikea wire sh...
Watch the woodworking how to video clip to learn how simple & easy it can be to make dead on cuts every time. The woodworking lessons in the YouTube video are simple, yet profound. It’s all about quality & the efficiency of each cut made in the shop. A stop block is essential to great woodworking. The stop is basic & fundamental to both woodworking and carpentry. Beginning woodworkers may have a tendency to measure each cut before it is made even though all the cuts to ...
How to make wood inlay banding the easy way. This YouTube woodworking video focuses on a simple way to make an elegant & decorative wood inlay banding of maple & walnut. The two contrasting hardwoods create a striking design that can be inlaid into furniture, jewelry boxes, pictures frames, and much, much more. Beginning woodworkers as well as experienced craftsmen can watch the video and quickly learn how wood inlay banding can be easily made on the band saw. The technique for ...
Like many of us I have looked at all of those pictures of other people’s roubo workbenches with a jealous eye for quite some time. The ones built with Benchcrafted hardware just seemed to be top notch in quality, and they look like woodworker candy. I’ve had this build on my to-do list since 2011 because I don’t have a woodworking bench with woodworking vises or anything to hold my work down. I’m forced to use my old Unisaw as a bench and the best I can do is use a cla...
This woodworking tutorial features the mitre joint. If you’ve done carpentry or woodworking there probably was a time or two that the mitre joint was a challenge. This video shows how the mitre joint can be cut and fit with great accuracy, done safely, and with ease by using a mitre sled on the tablesaw. What if you could take your wood projects to another level? Now you can. You can feel comfortable cutting one mitre or hundreds of mitre joints as the mitre sled method ensures ac...
I’d been living with this board of burr / burl or pippy oak in the workshop for five or six years and must have picked it up and put it back down at least a hundred times (approx!). I have done quite a few boxes in the past with lids something like this: but I always intended that this piece would be used in a different way, and for something a little bit special. Though I’ve made many boxes, I have never thought of doing one for me, so this challenge presents an opportunity. ...
Ever need an extra clamp? Watch and learn how to easily make a very simple and effective woodworking clamp. How to make poorboy Parallel Clamps ........... Visit…The Apprentice and The Journeyman............Learn more, Experience more!
Version 1.2a At this point I decided to get more “radical” in my design approach. I removed two of the cross rails (found out through experience that I didn’t need them anyway). Then I took the corner poles out of the flanges and put a “sleeve” on the side of my table for the corner poles to slide into (see photo below). Electrical conduit clamps work great for attaching the sleeves. This design also allowed me to adjust the height of the router sled in...
RIGHT CLICK ON THE PICTURE, CLICK ON ” OPEN IN NEW TAB ” TO SEE THE FULL PICTURE.First, make leg template.Cut stockRound over one edge, 2 left, 2 right.Using table saw, make your spline cut.Cut your splines and check for fit. This is what you should end up with.Start laying out your leg build up.Make sure your build up clears the template.Glue it up.Line up the template with your stock and trace it.Cut it out on the band saw.Cut both sides on that face then tape the scrap back on ...
- My Journey As A Scroll Saw Pattern Designer - 1561 parts
- Extremely Average - 324 parts
- Workshop Development - 107 parts
- Just for Fun... - 96 parts
- A journey into the workshop. - 89 parts
- Daily Update - 87 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 76 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- ScrollSaw Information and Resources - 68 parts
- Sheila Landry (scrollgirl) - 1586 entries
- frank - 417 entries
- degoose - 395 entries
- dbhost - 390 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- Martin Sojka - 296 entries
- mafe - 276 entries
- William - 258 entries
- Betsy - 221 entries
- Stevinmarin - 212 entries
- shipwright - 212 entries
- Gary Fixler - 204 entries
- Todd A. Clippinger - 199 entries
- stefang - 188 entries
- Rustic - 188 entries
- Chris Davis - 183 entries
- BritBoxmaker - 181 entries
- Smitty_Cabinetshop - 175 entries