Woodworking blog entries tagged with 'circular saw'

  • Advertise with us
View JoeyG's profile

New Tools Are Cool #2: Bosch CS5 Circ Saw

01-27-2012 12:11 AM by JoeyG | 10 comments »

So my last package for the day just showed up. There should be a few more over the coming days but for now lets talk about my new circular saw. As I said in the last episode I need to retool my shop for making cabinets. Since I cannot fit a large table or panel saw in my shop I will have to cut my sheet goods with a circular saw. I am replacing a very old Black and Decker that looks like hell and cuts even worse. I believe I have more chance of cutting a perfect circle than a straight ...

Read this entry »

View ruddhess's profile

Southern Yellow Pine Work Surface (workbench) #23: Workbench Modifications & Additions

03-31-2015 02:18 AM by ruddhess | 0 comments »

I made about 10 half inch deep cuts to remove most of the waste wood for the groove. My white pine 1X2 saw guide and clamps. Here is the 1-1/2” wide by 1/2” deep groove the length of the top board. I can’t believe how good it looks! I made and used my “poor man’s router” that Paul Sellers talks about in one of his videos. It is a poor man’s router made poorly by me. But it worked well enough to get the bottom of the groove flat. I’ll ha...

Read this entry »

View RaggedKerf's profile

Lego Table #4: Assembling the base

11-22-2015 07:42 PM by RaggedKerf | 0 comments »

Today was a pretty productive day in that I got all the lower parts of the table ready for finishing, but my final output didn’t look much different than yesterday. To start, I flipped the completed bottom frame over a piece of 1/2” plywood and traced the outline. I then broke out the circular saw and using a straight piece of poplar plank, figured out the blade offset and clamped the straight edge down. I placed this whole thing on top of a sheet of 1 1/2” thick (I think) foam insulation ...

Read this entry »

View bandit571's profile

Another pile of pine #1: Part 2, a top is formed up

03-31-2015 03:08 AM by bandit571 | 7 comments »

Well, got the top almost flat on the “face side” the other day Used a scrub jack plane to get things down to almost flat, other than all them scalloped areas. Got out a little bit bigger, and wider jack plane. This time, it is used like a try plane, going at the diagonals to the grain, until all them scallops are gone. Top still wanted to bow up a bit, so I clamped that end down flat, and left it sit a while…. Well this evening, flipped the top over to work on t...

Read this entry »

View teenagewoodworker's profile

Printer Table #1 (Basic Construction)

03-09-2008 02:50 AM by teenagewoodworker | 8 comments »

Hey Everybody In this episode of the Teenage Woodworker I go over some basic cabinet construction in the first part of a three part series where i make a printer table. There are a lot of technical things that i go over but try to stay with me for the whole episode. As always since i am only using a digital camera to film the sound is a little bad. so try to bear with me it helps to turn up the sound and sit a little bit away from the computer. this improves the sound a little bit. ...

Read this entry »

View ChunkyC's profile

New base for an old Porter Cable Circular Saw #1: Part 1 - ready for setup

10-03-2009 12:15 AM by ChunkyC | 0 comments »

Right hand sideLeft hand sideThe underside I not certain that this qualifies for a “project” but it’s been raining here for the last two days (on vacation not withstanding!) so I had to do something. The base started from a 12×12 blank of 1/8” hardboard and trimmed down to final size of 12×11-1/16. I made the base a lot wider on the left hand side so that I can use the saw with my good hand (left hand). The way is was before, the motor would hit the c...

Read this entry »

View Gary Fixler's profile

techniques #1: Found a way I like to cut straight-end, non-through rip and crosscuts in plywood

03-14-2009 11:18 PM by Gary Fixler | 0 comments »

This is probably a common technique, with a name, but it only occurred to me today. I gave it a shot, and it worked out really well. I’m going to use it from now on for non-through cuts, and by that, I mean rips and crosscuts that don’t go from one end to the other, but do cut through bottom and top of the ply. Basically, once I set the blade height, and fence, I run the cut up to a 2” mark I make from the leading edge. Then I back it out, flip it over, and measure the di...

Read this entry »

View Scott R. Turner's profile

Built-In Bed #1: Pleasing the Customer

11-07-2010 11:57 PM by Scott R. Turner | 6 comments »

I always enjoy reading project blogs here on LJ, so I’ve decided to attempt one myself. Hopefully some folks will find it enjoyable! I’ve built a few beds over the past years, the most recent being this one that my son uses: It’s solid maple and has been beat up a little over the years and acquired glow-in-the-dark stars, all of which adds to its character, and I don’t mind in the least. I like that the bed has been host to both my children and that they...

Read this entry »

View benihun's profile

Patio #2: Roofing

07-21-2008 10:38 AM by benihun | 8 comments »

The cover of the roof with wood is finished. I made side rails on my own way. The view from underneath is satisfying for me.

Read this entry »

View MarkTheFiddler's profile

Cocktail table for my wife's room. #2: Top is being mounted

09-27-2012 03:21 AM by MarkTheFiddler | 3 comments »

Howdy, I started mounting the table top today. It occurs to me, in hindsight, that I may have caused myself a lot of frustration. I’ll find out soon enough when I try to place the diamonds. Be that as it may, it’s turning out pretty well but you can still tell that a rookie is doing the work. I was able to use the warped pieces but now I have a few pieces that are slightly higher than others. I just bought myself more hours of sanding. I’ve also got a few gaps. A f...

Read this entry »

« prev 1 2 3 4 5 next »
42 entries

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics