Well, let me start by saying this is my very first post. I love designing new furniture (Dressers, Couches, Tables, Cribs, Shelves, Beds, Etc.) and have found it a real joy building what I design. I unfortunately do not have any professional tools or many tools in fact, but I do what I can with what I have. Money doesn’t grow on trees… So, my objective is to try and help you and myself build fairly inexpensive furniture while still being good quality in appearance and st...
Hey everyone, It was suggested that I start a discussion on how to find and harvest burls. Please give your input also. I don’t deal with straight grain that often. I cut and sell burls for a living so here is what I know. It is illegal to harvest a burl without permission. of course if it is on your own property you can give yourself permission. What I do is put an ad on Craig’s list saying I want your burls. Most people don’t know what burls are. So you don’t get that many calls....
so just like every other woodworker at one point (what’s up with the other every other woodworkers is beyond me…) I was researching and learning about ways to sharpen my chisels, planes, and other blade tools in the shop. Since I am the weekend warrior at this point, and I do not need to resharpen my tools THAT often, nor THAT much, I figure that I can do without any expensive powertools (there are several of those on the market) to sharpen blades and I dont really have the spa...
We need a Murphy bed next winter in Arizona and I did not want to buy the hardware. That takes all the fun out of designing it yourself and costs $360. So I looked at a lot of bed designs and settled on one that used HD pivots, gas springs for counterbalance and a swing out leg support rather than the fold down kind.The parameters were a twin mattress (7×39 x 75), had to flip long ways and enough room inside for making the bed. Then I had to decide on the pivot points, the foot pivot ce...
Updated 1/16/12 I spent a lot of time developing a way to let the lid swing down into the box, yet still maintaining a fairly tight reveal on all four sidesThe difficulty is the lip itself. It doesnt allow the back of the lid to drop into the box, so thats where we need to cut it away a little deeper at the back. I call these pockets.The other difficulty is in getting the hinge placement spot on or it wont open at all or not far enough to stay open. Here is how its done: Use the same pa...
This Week I show you how to make a folding out feed table for your table saw. This design was based after an article and plan found in a 2009 issue of Woodworker’s Journal Magazine. Originally the plan was designed for a Cabinet saw with a Biesemeyer Fence System, so I had to make some slight modifications for my Porter Cable Saw. In this 3 part video series I show you a step by step on building this project as well as talk about the modifications I had to make. The Article and plans ca...
When I returned to woodworking several years ago my nephew had been talking about a particular style of “coffee” table he’d seen online somewhere and was describing it to me. Since he’d just announced plans to marry, I told him I’d make him, and his fiancée, the table as a wedding gift. He showed me some online photos of the table, which I used as the basic, general design plan. The joinery I chose is original but the style was taken from the photos. This piece is the result: ...
Updated 1/15/12 Now we need to cut a recess in the lid for the medallion to set down into.DONT cut your medallion until you have routed out the home for it.I typically make the medallion about 1” to 1.5” smaller on all sides than the lid depending on the box size and the piece of wood I have for the medallion. We are now going to make a simple jig for a router to set on and run back and forth making several passes of incrementally deeper cuts. There are a several ways to do ...
Intro: Hello to all and welcome to the first installment of Intarsia Basics. Before we can start cutting we need to select the wood we want to use and get our pattern ready. Wood Choices: I prefer to start with stock that is one inch thick because that gives you a lot of depth that you can work with. It will require a little more sanding on some areas but it will help to give your piece a 3D look. It is your choice if you prefer to stain your wood to achieve the colors or use exot...
Updated 1/16/12 This is where you need to decide how you want to open your box. I mentioned at the outset about some of the different boxes I have made and how they hinge differently from one another. All are good, but you may have a preference in style or it may be your ability that decides for you. The pin hinge is what we will mainly be focusing on and was used on this box. Chapter 10 will discuss this style. The Deco box uses a standard brass butt hinge with a stop stra...
- My Journey As A Creative Designer - Woodworking and Beyond - 1781 parts
- Extremely Average - 324 parts
- A journey into the workshop. - 110 parts
- Workshop Development - 107 parts
- Toy costruction - 106 parts
- Just for Fun... - 98 parts
- Daily Update - 87 parts
- Life as an Amateur Woodworker - 81 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- Woodworking on a Half-Shoestring - 77 parts
- Sheila Landry (scrollgirl) - 1806 entries
- dbhost - 432 entries
- frank - 417 entries
- degoose - 397 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- mafe - 307 entries
- Karson - 305 entries
- Martin Sojka - 296 entries
- William - 258 entries
- shipwright - 254 entries
- robscastle - 235 entries
- Dave Rutan - 228 entries
- Betsy - 228 entries
- stefang - 221 entries
- Stevinmarin - 212 entries
- Todd A. Clippinger - 207 entries
- Gary Fixler - 204 entries
- A Slice of Wood Workshop - 204 entries
- Smitty_Cabinetshop - 195 entries