My old rear deck was falling apart. The ledger board was not treated lumber and had been installed withouta drip cap and was half rotted, since it is the first thing put up and the last taken down, the entire deck hadto be torn down. No pictures of this, it was just too badly built. The county building inspectors said that 4X4 post would be OK as supports, but then they wanted more 4X4 post bolted to the sides of the deckas guard posts to support the railing. I decided to simplify life and...
hello fellow jocks and jocketts…this is my cherry wood gloat for the year, and probably the only one i will have, i was fortunate enough to have a man advertise that he wanted someone to cut his cherry tree down and use it for furniture and the likes…i was the first to call , i went and checked it out and was like the kid at Christmas, i knew what the present was, i just didn’t know exactly what is was going to look like, the day i cut it it went to the sawyer and now about ...
I have always cut my green logs either on the ground or on top of other logs. Well a few weeks ago I was cutting a log and it decided it wanted to dance a little bit. Now I don’t care if a log dances or not I just don’t want it to move while I have a moving 20” chainsaw in it. This got me thinking there has to be a way to hold the work safely for cutting. So I took to the internet looking for sawhorses for chainsaws. I did find a few commercial units but they were all listed in E...
Views of Wood Expression ....you decide your view,my minds made up i am one,all one piece of wood….—by flp ————————————————————————————————————————————————————...
Last step in the process (well not the last – but close to it – still have to get back over there and paint, or otherwise seal the endgrain, which hasn’t done much in the way of checking with all the freezing temps and the moisture we’ve been getting) ...I set up a level ‘foundation’ for the lumber stack. Made sure it was up off the ground and spaced the beams just under 2ft apart:.........Here’s a couple shots of the progress. My wife helped me h...
Here’s a little more ‘milling around’ for fun:........ This board turned out to have some really interesting spalting…........ And, upon closer examination:........... One with our stacks:........ And our final parting shot! ........ This concludes the milling process. What a blessing it was to have Mike’s support in this process. I can thank LJ for that! And a HUGE thanks to Mike directly! That was a lot of fun last Wednesday. Just amazing what can come f...
At the end of this short video you’ll see me look up at Mike. If you listen closely you can hear the saw hit some more metal….... .... At some point after the next few cuts we hit our 3rd and 4th nails within the same board:........ But, look what we have here!........ Here’s a shot of the “scene” at this point (there’s a few board feet of sawdust):........ We’ll finish up the sawing in the next installment…We uncovered a real gem just a bit ...
After the slabbing cut, we continued to cut the first half of the log. Here’s a short video of Mike on the saw….... .... After a few cuts we hit a nail…pulled the saw out and cut from the other end…chipped a tooth but nothing really terrible; the chain was still relatively sharp, so we continued to cut!............ Here’s the spalting a bit closer up…it gets even better in the 2nd half!....... .... A bookmatch shot for fun…........ MORE TO COME!....
On the same cold, crisp, gorgeous day in Sunny Seattle…the next thing we did was mount a 2×12x12 to the top of the 1st half of the maple log as a guide board to establish our first flat face from which we could continue to cut with just the chainsaw mill. The 2×12 had 2×2 runners screwed on to it to keep it flat and a wee bit more ridgid. One hooked over the edge, while the other was inset a few inches to “shim” the board to “level” it out (all ...
- My Journey As A Creative Designer - Woodworking and Beyond - 1742 parts
- Extremely Average - 324 parts
- Workshop Development - 107 parts
- A journey into the workshop. - 105 parts
- Just for Fun... - 97 parts
- Daily Update - 87 parts
- Life as an Amateur Woodworker - 79 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 76 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- Sheila Landry (scrollgirl) - 1767 entries
- dbhost - 418 entries
- frank - 417 entries
- degoose - 397 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- mafe - 304 entries
- Martin Sojka - 296 entries
- William - 258 entries
- shipwright - 245 entries
- Betsy - 228 entries
- stefang - 220 entries
- robscastle - 218 entries
- Dave Rutan - 213 entries
- Stevinmarin - 212 entries
- Todd A. Clippinger - 207 entries
- Gary Fixler - 204 entries
- Smitty_Cabinetshop - 193 entries
- A Slice of Wood Workshop - 190 entries