This week I embarked on my latest creation adventure which I made out of pallet wood boards… a patio table with benches! I wanted this to look prestine and clean while maintaining a sort of rustic feel that the pallet wood gives to it. So I went through my stock of pallet boards and pulled the best quality / matching sized boards I could find and used them in the project. The only things I bought for this project were the screws (I normally use the pallet nails for the ultimate recyc...
Hello All, This is not a new tip, but I thought I’d mention it in my blog anyways. As always see my blog at: http://blogspud.blogspot.com/ Ok so working with pallets is not always perfect, the wood is definately not top grade by any means and I will not pretend it is. So occasionally you are going to want to use a wood filler at some point. Now Elmer’s, as well as Varathane and Rustoleum sell wood filler that is pretty good, but the cost can add up significantly and this is ...
Also see this on Blogger at: http://blogspud.blogspot.com/2012/07/pulling-boards-from-pallet-without.html Hello all, I have been working with pallets lately and I thought to myself “what if folks want to do this too?” So I decided to share what I found to be the best way to remove a board from the pallet without destroying the pieces. Step 1: Cut the boards off of the top of the pallet.From the edges as close to the brace boards as possible, cut the top Boards (top bec...
See this post and more at Pallet Craft Hello Readers! You have probably seen lots of things made from pallets on the Internet, from chairs to storage and much more. However there is a key distinction between building projects from pallets and building projects with pallet wood. While both of these methods are recycling the pallet wood and putting them to good use (which I applaud), I want to show that the wood from these pallets can be turned into beautiful pieces instead of usin...
For all the images on this entry and others please go to my blog: pallet craft! Hello All, This is part of my series Pallet Craft on my blog. It is pooring out once again, and because I have nowhere else to work on my projects except for my mobile work station (outdoors), I decided to blog about why I do what I do. Woodworking in general came to me as something foriegn that I had never really given a lot of thought of doing (I mean common, I was a tech student), I thought of it as so...
Hello Readers! Well from the title of this entry, you can probably guess what this is about. Yes, Halloween has not even come yet; Yes, Thanksgiving is more than a month away! But I have learned that planning and starting now will give me the time I need to get the projects done. Why wait until the snow is falling and the bitter cold bites? So what will I be building? Well that is a secret and I will post all about them on December 26th and 27th. I don’t want any gift receivers to...
Hello Readers! Just a quick update: I got plans for the maloof chair, so I will be studying these extensively for my build. My wife has been perusing pinterest and the internet and has stumpled upon a few DIY pallet creations that she loves and wants me to recreate. Well its safe to say I am at no shortage of projects now… Here are a few of the projects she has in mind (more at my blog, I could not fit them all in this post): Now you might have noticed if you read m...
For more on this and other posts, visit: Pallet Craft! Hey all! Today I have something cool to share! So we just got a bunk bed (see my blog for type) second hand for my daughter to have in her room.As we were building it we were saying to ourselves that we wanted to put her stuffed animals on the bottom, but we did not have a second mattress yet and the bottom only had a metal wire support. It was safe to say we wanted to put something on it that would be better than bare metal! My wif...
Good Morning All, Ever run into a piece of wood (pallet wood in this case) and wonder; “How the heck did that warp like that?” Working with pallet wood can be a twisted mess of metal, warp and work. These things lead to a lot of distress trying to make them work for a project, leading you to want to pull your hair straight out. Sometimes you just have to llook at it and say in the words of the great Fozzie Bear, ”What the waka?” This is where I stop and cl...
Hello Readers, That’s it! I have had enough for one day!... Well that is what I should have said, but if you know me I can’t seem to help myself when it comes to frustration and working on things. I know I should stop, after all, all this frustration is just leading me to rush through critical parts of the project! So I change my attitude towards the project, perhaps my project is frustrated with me because it has seen enough work for one day? Perhaps I am overworking th...
- My Journey As A Scroll Saw Pattern Designer - 1265 parts
- Extremely Average - 324 parts
- Workshop Development - 95 parts
- A journey into the workshop. - 88 parts
- Daily Update - 87 parts
- Just for Fun... - 82 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 75 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- The Craftsman's Path - 67 parts
- Sheila Landry (scrollgirl) - 1287 entries
- frank - 417 entries
- degoose - 388 entries
- dbhost - 370 entries
- Ecocandle - 325 entries
- MsDebbieP - 311 entries
- Karson - 301 entries
- Martin Sojka - 297 entries
- William - 257 entries
- Betsy - 221 entries
- mafe - 216 entries
- Stevinmarin - 212 entries
- Gary Fixler - 204 entries
- Todd A. Clippinger - 187 entries
- Rustic - 184 entries
- Chris Davis - 183 entries
- shipwright - 168 entries
- PurpLev - 163 entries
- BritBoxmaker - 161 entries
- stefang - 148 entries