I call this the “Opposing Arches” table. This commissioned glass top display table, or buffet, is 50” wide at the base, 14” deep and 29” tall. It supports a piece of glass that is ¾” thick by 18” by 66”. The construction is shop sawn zebrawood veneers, laminated on two layers of 1/8” poplar bending ply, on a curved torsion box inner core. The curved members are then framed in sold quarter sawn sapelli. The divider box is shop sawn veneer, cut from a very fine grained piece of Macassar...
Hey Everyone, well its been a while since I have posted a project video. Things have gotten busy at the shop with the new ASDOO Music Cajon Drum line. Well I have a nice weekend project for you this time. It is a Mini Buffet with Hutch. The plans for this mini buffet with hutch are available at The Newfoundland Woodworker Website in the free plans section. This is Part 1 of the project. I hope you enjoy.
The final installment of the Hutch with buffet build Thank you all for following along.
We continue with Part 4 of the Buffet with Hutch build. In this video we focus on the raised panel doors.
After getting all the old finished off the buffet, actual this piece was very nice. You may see that in the photos I added a second 1/4 inch plywood piece to the second shelve for strength. I will finish this with a veneer for a better looked. As you see I still have two burns in the top of the unit however I am going to stain the top to make it less seen.
My wife says I can’t do anything else before I start on her Kitchen. Well except for her hall table and ??. Of course there is also the Summer Contest. This is going to be a multiple phase project. I need to do something with the floor. We are on a cement slab floor and it is killing both of our legs. The kitchen had a Pergo floor when we bought the house, but we had a frozen water line before we moved in and the Pergo floor got curled edges, so it was all pulled up. I don’t...
Well it’s been a weekend, not a lot of work done, but enough to make you think that you’ve accomplished something. Two screw-up’s, two corrections, one modification. Only had to recut two pieces of wood, not too major. Could have been a lot worse, and re-planed 6 boards that were too thick.I left off with the making of the lower case for the Buffet / Hutch. I stated that I needed to do some veneering and also some engineering for the mid drawer slides. I’ve done the veneering and done no ...
Cutting the tenons and fixing the mortises. In an earlier blog I was talking about story sticks and laying out the mortise cuts for the legs. I further stated that in my reply to Bob that: “The rails at the top and bottom have a 1/4” grove cut in them to allow for plywood for the insert. The top rail ended up with a 1/2” cut for the tenons, where it touched the panel, while the bottom one had still the 1/4” cut. Why the difference. ??” Well I found out why the difference. I miscalculate...
Watch this video to take a short tour of the furniture I’ve made in my living room and dining room. These rooms are the first thing you see when you walk into our house. Unfortunately, the living room had very little furniture that I’d made. My wife and I came up with a furniture plan to resolve that and I’m well on my way to filling the living room with hand-crafted furniture. The rocking chairs are quite comfortable and I love the sweeping lines. The foot stools...
Well I started the Buffet / Hutch. If I don’t get started I won’t have anything to say without getting myself in trouble, when my wife asks me what I’m making in the shop. I started out by making a full size template on plywood for all of the milling that needs to be done on the legs. Can you believe that those two templates have all of the instructions for milling 8 surfaces on the legs?Now you may ask what do you mean by 8 surfaces. This is the way that I was taught when you make ...
- My Journey As A Scroll Saw Pattern Designer - 1186 parts
- Extremely Average - 324 parts
- A journey into the workshop. - 87 parts
- Daily Update - 87 parts
- Just for Fun... - 81 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- The Craftsman's Path - 67 parts
- As The Lathe Turns - 67 parts
- Workshop Development - 65 parts
- Sheila Landry (scrollgirl) - 1208 entries
- frank - 417 entries
- degoose - 387 entries
- dbhost - 331 entries
- Ecocandle - 325 entries
- MsDebbieP - 300 entries
- Martin Sojka - 297 entries
- Karson - 293 entries
- William - 249 entries
- Betsy - 221 entries
- Stevinmarin - 212 entries
- Gary Fixler - 204 entries
- mafe - 204 entries
- Todd A. Clippinger - 187 entries
- Chris Davis - 183 entries
- Rustic - 183 entries
- PurpLev - 162 entries
- shipwright - 160 entries
- BritBoxmaker - 159 entries
- scottb - 144 entries