Since it’s so cold outside. ————— DID YOU KNOW THIS???? It was necessary to keep a good supply of cannon balls near the cannon on old war ships. But how to prevent them from rolling about the deck was the problem. The best storage method devised was to stack them as a square based pyramid, with one ball on top, resting on four, resting on nine, which rested on sixteen. Thus, a supply of 30 cannon balls could be stacked in a small area right next to...
As woodworkers we also need to cut metal once in a while. Also, having the ability to cut metal will allow us to create custom handles as I have on past projects. The question is how do we get a clean cut? Hacksaw? Reciprocating saw? Nope – portaband is the answer. The portaband is a powerful, smooth cutting portable bandsaw and a tool that I recommend for any custom woodworkding shop. Hope you enjoy! Your friend in the shop- Todd A. Clippinger Share the Love~Share ...
Well, I thought this would only take one evening, but it was more like 3 evenings and a morning! The hinges arrived from Lee Valley on Monday on time. From past experience, I knew the #4 screws are a little small in diameter and were going to be too long for the lids. Last time I used #6, but they were a little big and I had to open up the countersinks to get them to fit. This time I went with #5 screws – 1/2 inch for the lid and 3/4” for the box. Now that the hin...
Made a little video with the mistake I made while cutting a piece of brass… Luckily I wasn’t hurt and learned my lesson hopefully you learn something too. View on YouTube
It has been a while since I posted anything as a friend reminded me couple days ago. So I thought I would do an update on couple projects I have been working on. On an earlier post I had shown the start of a restoration on a Boulle clock. We had restored the top part, since I have been working on the 2 lower elements. I did not took a lot of picture of the restoration of the middle section But I documented better the restoration of the lower section that was partic...
I’ve been working on this sculpture for a while at TechShop and at home. It’s taken a long time but I’m finally finished and wanted to share it with you. Video of it In Action Here’s my build-journal of sorts. I started out with a vague idea of making a digital Victrola. I thought about making an iPod dock attached to an old horn but quickly abandoned the idea for a couple of reasons: it’s been done already (!) and it didn’t satisfy my artist...
Most all of my projects Have my brand on it in one place or another. Now, I don’t have a branding iron. But what I do have is a way of Chemically etching Brass plates with my logo on it. Here Is an example of one Now using the method I am going to show you, you can easily create custom plates as well for your projects. Not just logos but even plaques and signs.. Here are a few examples Here is how you can make an etched brass plate of your own….Now the first 2 vi...
My second oldest daughter needs a birthday gift and I have only days to complete it. Don’t you love those last minute projects? She is into carving, but only has the carving set with the “end blades”. So why not build a carving knife. So last knight I started with a block of pallet wood, a rod of 3/16 brass and a sawzall blade.The shape I was going for is shown here: I took a sawzall blade and cut it in half with a sheet metal cutter. (this stuff is hard to cut) After ...
One of my great weaknesses is brass. Another is shop made tools. I like the look of brass, especially when it has aged. I must have a steam punk side that is trying to come out. I made these 3 tools out of brass. The square and the Fibonacci gauge can certainly be made of wood, but the gauge is so esoteric it just seemed like it would be better in brass. The square I made partly as an experiment, partly because I needed a small square and begrudge the $8 or more it would cost in stee...
Fired the load yesterday. 14 hour kiln cycle …. cone 1 … around 2000 degrees Unloaded this evening. NO TILE BREAKAGE …. first time EVER !! NO Cracks or anything !! Think the p-clay is the clay for me to use ........... Photo my first complete 6 panel set !!! Never in over 8 trys have I been able to get all 6 to survive. Even when firing mutliple sets one would always break. photo of the metal coatings material photo of primered tiles ...
- My Journey As A Creative Designer - Woodworking and Beyond - 1742 parts
- Extremely Average - 324 parts
- A journey into the workshop. - 107 parts
- Workshop Development - 107 parts
- Just for Fun... - 97 parts
- Daily Update - 87 parts
- Life as an Amateur Woodworker - 80 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 76 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- Sheila Landry (scrollgirl) - 1767 entries
- dbhost - 420 entries
- frank - 417 entries
- degoose - 397 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- mafe - 304 entries
- Martin Sojka - 296 entries
- William - 258 entries
- shipwright - 246 entries
- Betsy - 228 entries
- stefang - 220 entries
- robscastle - 218 entries
- Dave Rutan - 214 entries
- Stevinmarin - 212 entries
- Todd A. Clippinger - 207 entries
- Gary Fixler - 204 entries
- Smitty_Cabinetshop - 194 entries
- A Slice of Wood Workshop - 190 entries