https://www.youtube.com/watch?v=2yv2FB-qURs Part 1: https://www.youtube.com/watch?v=PXDdAhpPCok Thanks for watching, I hope you like it! Disclaimer: I’m not sure but I’d imagine there will be some Safety Sally comments about the placement of my stop when I’m cutting the tongues. Please trust me, I’m comfortable and know the limits of my saw and I respect it, in this situation it was acceptable because I was taking off such a small amount of material
Recall Date: May 11, 2016Recall Number: 16-158 Robert Bosch Tool Recalls Grinders Due to Risk of Burnshttp://www.cpsc.gov/en/Recalls/2016/Robert-Bosch-Tool-Recalls-Grinders/ Recall Summary Name of Product: Bosch small angle grinders Hazard: The grinder can overheat while in use, causing the brush covers to melt and expose the end of the brush holder, posing a risk of burns to the consumer. Remedy: RepairConsumers should immediately stop using the recalled grinders and contact the ...
Whew! Finally figured out this whole blog series thing :O Yesterday and today was all about building the casework for the miter saw station. Realizing that the floor is less than even across it’s surface, not level from side to side and the casework is almost 10’ long, I decided to make the assembly in three parts. This will allow me to use leveling feet on each cabinet to compensate for the unevenness of the floor across the length of the whole assembly. I’ll first ...
Recall Date: August 26, 2015 Recall Number: 15-227 Robert Bosch Tool Recalls Dremel Rotary Tool Due to Burn Hazardhttp://www.cpsc.gov/en/Recalls/2015/Robert-Bosch-Tool-Recalls-Dremel-Rotary-Tool/ Recall Summary Name of Product: Dremel® MICRO™ Model 8050 Rotary Tool Hazard: The tool’s circuit board can overheat and melt the tool’s enclosure. If the tool is being held while overheating, it could present a risk of burn. Additionally, some tools may lose their speed control cha...
Here’s a video where I demonstrate a couple of ways to mount a jigsaw in a table, and a useful technique for minimizing tearout.
hi all dose anyone knows who fix bosch routers the micro ajustment ethere broke or stop working and can,t find anyone on the internet that fixs them near where i live in new england ,or ct please help kayakdude
WASHINGTON, D.C. – The U.S. Consumer Product Safety Commission, in cooperation with the firm named below, today announced a voluntary recall of the following consumer product. Consumers should stop using recalled products immediately unless otherwise instructed. It is illegal to resell or attempt to resell a recalled consumer product. Name of product: Miter Saw Units: Approximately 22,149 Importer: Robert Bosch Tool Corporation of Mount Prospect, Ill. Hazard: The lower guard...
made a video on basic maintenance and tune up for my freinds and thought I’d share it… hope you like it.
I decided on the Bosch 1617EVS(PK), so kept my eyes peeled over the last week or so on the different retail sites, including craigslist and ebay for a possible used one. Amazon’s price for the “Bosch 1617EVSPK 12 Amp 2-1/4-Horsepower Plunge and Fixed Base Variable Speed Router Kit with 1/4-Inch and 1/2-Inch Collets” was $200 (pretty competitive based on my searches but not a huge bargain), but today I realized that Amazon is having a Bosch tool promotion until May 31st. ...
Have not been here much in the last year or so. I got a new position at work which has taken up more time in a good way. I have actually built a bunch more of the kitchen cabinets which I will post later. I am finally building some removable sliding windows for the porch. I put some fixed windows in a few years ago, but it was long enough that I completely forgot how to do the job smoothly. So I am going to document it this time. In this blog: How to make the frames. Here are two of the...
- My Journey As A Creative Designer - Woodworking and Beyond - 1752 parts
- Extremely Average - 324 parts
- A journey into the workshop. - 109 parts
- Workshop Development - 107 parts
- Just for Fun... - 97 parts
- Daily Update - 87 parts
- Toy costruction - 86 parts
- Life as an Amateur Woodworker - 80 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 76 parts
- Sheila Landry (scrollgirl) - 1777 entries
- dbhost - 428 entries
- frank - 417 entries
- degoose - 397 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- mafe - 304 entries
- Martin Sojka - 296 entries
- William - 258 entries
- shipwright - 250 entries
- Betsy - 228 entries
- stefang - 221 entries
- robscastle - 218 entries
- Dave Rutan - 217 entries
- Stevinmarin - 212 entries
- Todd A. Clippinger - 207 entries
- Gary Fixler - 204 entries
- Smitty_Cabinetshop - 194 entries
- A Slice of Wood Workshop - 192 entries