Update: 7 september 2010. As I do not have a lot of spare time for woodworking at the moment, I am submitting this blog for the contest, I hope you guys don’t mind that it is a little old Here is a link to the final projects- http://lumberjocks.com/projects/2542http://lumberjocks.com/projects/2559 http://lumberjocks.com/assets/pictures/projects/9436-438x.jpg?1233630507 After several e-mails requesting the plans for the Dan Walters cutting board I copied I decided to put some...
OK, so now that the kitchen challenge is all over, I guess it’s a good time to post a blog regarding kitchen items … or… hold on… um – oops. too late. Oh well, I guess I’ll blog this anyways. So, the plan is to make a bread board. for the time being, the design shall remain unseen and will reveal in details as this blog series will progress. The board is primarily made of hard maple that I am recovering from bowling alley floors (I still have about ha...
This blog will show how I make a 12” bowl blank from 1 BF of lumber. Cut a 12”x12”x3/4” square and draw an X from corner to corner to find the middle. Using a compass draw a circle in the middle of the board the size you want the bottom of the bowl to be. In this case around 4”. Draw concentric circles spaced the thickness of the board (in this case 3/4”) Drill 1/8” holes at 45 degrees on the 4 inner circles to insert a scroll saw blad...
The remainder of the maple came down today and I got a shot of the main trunk section that I plan to mill. It’s definitely going to be spalted throughout. This bole is 35-40” in diameter and the arborist was able to leave it intact from base to crotch! It’s 11’ long. It’s partially cracked on the side you can’t see and does have some splitting, so it probably won’t yield wide boards. I think it is sound enough to go through with this venture. Th...
I’ve had several LJ’s request pics of the jig I made for the wavy Larry board. I’ve snapped a few pics and sent PM’s with bits and pieces of info individually. Mikethetermite asked for some info a few days ago and I decided to bit the bullet and take the time to do it as a blog. Here goes- On my band saw table I have a sacrificial board- 3/4” plywood squared and framed to the table. The back frame piece unscrews and swings up to put the board on and off the ta...
One of the pleasant things about moving from a beginner to a more intermediate stage in woodworking is that you start paying attention to things you didn’t really focus on before. My work tonight, for example, involves a little more thought about grain orientation in glue-ups. I am still working on cutting boards, I have to have a dozen made in the next week or so. As I am moving along, I have had to give some more concentrated thought in regards to the wood pieces I salvaged and how...
OK, so it all started when I was trying to write a blog to post as a tutorial for people starting out with SketchUp. halfway into the blog, I decided that a video would probably be easier for me, and easier for others. so I stopped the blog, and started capturing the video. Halfway through the capture I figured that I probably will need to go a little more basic and a bit more in detail in order to be more clear about certain things that I do – so I stopped the video. Then it hit me ...
Well, I completed my journey and this is my story. I decided to use the maple veneer Karson gave me for the border of the chest board. Here is a picture of it taped up from the back: The next task was to completely tape the seams with the three hole tape as seen here: This was a somewhat tedious job because of all the seams. I felt that the mitered corners came out quite well and I was getting excited about finishing the process of gluing it up. I did a test piece with some ...
When mentioning that Chinese woodworking does not use glue I always get the question how to edge-joint without glue. On a recent trip to Southern China I had the opportunity to see a very nice example on what it looks like. The Perl River Delta (roughly the triangle spanned by Hong Kong, Guangzhou and Macau) is quite pleasant in Winter but extremely hot and humid in Summer. Since electricity is quite expensive people there tend to use the AC orders of magnitude less than in the US. This pu...
In response to some questions about how this pattern is made… I’m not sure if this is the only method, but here’s how I did it. Here’s the original project I posted: http://lumberjocks.com/projects/53452 Hint: When you look at the board, long ways going left to right, every row is a different size, but every group of 2 rows are all the same size! Solution: First you rip strips like you would for a regular end grain board, but in a progression of widths from l...
- My Journey As A Scroll Saw Pattern Designer - 1558 parts
- Extremely Average - 324 parts
- Workshop Development - 107 parts
- Just for Fun... - 96 parts
- A journey into the workshop. - 89 parts
- Daily Update - 87 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 76 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- ScrollSaw Information and Resources - 68 parts
- Sheila Landry (scrollgirl) - 1583 entries
- frank - 417 entries
- degoose - 395 entries
- dbhost - 390 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- Martin Sojka - 296 entries
- mafe - 275 entries
- William - 258 entries
- Betsy - 221 entries
- Stevinmarin - 212 entries
- shipwright - 212 entries
- Gary Fixler - 204 entries
- Todd A. Clippinger - 199 entries
- stefang - 188 entries
- Rustic - 188 entries
- Chris Davis - 183 entries
- BritBoxmaker - 181 entries
- Smitty_Cabinetshop - 175 entries