My workshop is a small garage with a low ceiling.I waste a lot of time unplug & plugging-in my dust extractor. My main tools are:- DeWalt DW745 table saw- Bosch GCM12GDL mitre saw- Festool TS55 track saw- Mirka CEROS 650CV 150mm orbit sander I wanted to make a simple/cheap device to transfer suction to each tool in turn, I came up the the following which I could fix to my garage ceiling: Next a quick sketch in my notebook: I had some white showerboard which I thought would be...
As part of setting up my wood shop, I decided adding a dust collection system was high on my priority list. I did a fair amount of research (somewhere between due diligence and mild obsessiveness) and did my best to make the decisions that fit my needs. I decided to post some information here since I got a lot of good data and advice from others here (and other sites). Sorry if this gets a bit long. Please note that I recognize there are many opinions on the “right” way to ...
When I first set up my shop, I bought a Delta 50-760 DC. It works well enough, but when jointing and planing a lot of wood the plastic bag fills up fairly rapidly and it is a PAIN to take off, empty and then re-install. Once you get the hang of it, the process is easier but it’s never easy and it almost inevitably ends up with a bunch of saw dust all over. So I decide to invest in a Oneida Super Dust Deputy. By the time I got it, I had realized that the fact that the Delta was mob...
Vacuum splitter and a ‘dust can’this one is for Dan / Maveric. Yes the dust goes to Dan this blog is dedicated to him and his recovery… Why? Because Dan just had a terrible time and this might have some roots in the dust from the shop! I personally sometimes sneeze and cough when I am done with sanding and I have had my thoughts on this for a while.My Vacuum is a shop vacuum, but just a standard one from Atlas copco and I used simple 50 mm 2 inch plumbing to distribute it s...
I’ve recently been in the market for a new dust collector. I really care about filtration, but do I really need a shop fox or grizzly portable cyclone, or should I go for a cheaper single stage model. I am just a hobbyist with a small shop in a two car garage. Any recommendations?
Blast gate for shop vac50mm hose size. Back to wood…And dust.And more. Just had a three weeks influenza, could hardly breathe, so I thought it was time to kill the dust in my shop.Since I moved to this shop I always just moved the hose from one tool to the other, this also means sometimes not doing it, since I am really a human, or in other words; make mistakes and are sometimes more lazy than rational.But to set up my dust system again I needed some blast gates, since my number o...
Five years later, Workshop Remodel. Going from pretty to functional #11: Connecting, hanging, and shrinkng dust collection pvc
My method for making pipe hangers, connecting dust collection pipe for air tightness without tape, and shrinking pvc to hug blast gate flanges for small shop owners This is only my method of doing this. There are many good ways and your mileage may vary. I just thought I’d share it in case someone can used it. Thanks for watching. If the video doesn’t show below then you can see it here
I filmed the build on my YouTube Channel. Please check it out! Please like, share, and if you enjoyed the video subscribe! http://youtu.be/ACLFMAfV1fk I recently added a Clearvue Cyclone dust collector to my shop. I plumbed it completely with 6” and 4” PVC piping. I needed a way to close off each branch to maximize the performance of the dust collector. Commercially available plastic blast gates are way to cheap and clog easily. The metal blast gates that solve this issue are p...
Okay i’ve been asked to show how my shop vac dust deputy system works so here it is. I have the smaller ridgid shop vac from home depot under my ras inside the cabinet stuffed with insulation enough to dampen the noise but still let the motor cool and exhaust as it should. So fan no problems (-: The hose then goes to the dust deputy on the outside rear to the 5 gallon bucket it comes with, out of the top of the cyclone up towards the saws. I have it hooked into the home depot clea...
- My Journey As A Creative Designer - Woodworking and Beyond - 1742 parts
- Extremely Average - 324 parts
- Workshop Development - 107 parts
- A journey into the workshop. - 106 parts
- Just for Fun... - 97 parts
- Daily Update - 87 parts
- Life as an Amateur Woodworker - 79 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 76 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- Sheila Landry (scrollgirl) - 1767 entries
- dbhost - 419 entries
- frank - 417 entries
- degoose - 397 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- mafe - 304 entries
- Martin Sojka - 296 entries
- William - 258 entries
- shipwright - 246 entries
- Betsy - 228 entries
- stefang - 220 entries
- robscastle - 218 entries
- Dave Rutan - 214 entries
- Stevinmarin - 212 entries
- Todd A. Clippinger - 207 entries
- Gary Fixler - 204 entries
- Smitty_Cabinetshop - 194 entries
- A Slice of Wood Workshop - 190 entries