A Quick, Accurate Way To 45 Your Corners If you build boxes at all, eventually you tire of cranking your blade from 90 degrees to 45 degrees and back…I did. So I built this simple jig, and now I can cut all 8 ends of a box accurately in about 5 minutes, AND STILL LEAVE MY TABLE SAW SET AT 90 DEGREES. Assumption: I am assuming that you have already laid out the board for your sides and have cut all four sides of your box to length. Short side, long side, short side, long side...
Setting up saw blades for slot cuts in box corners. Here is a quick way to set up your saw for cutting spline slots using a spline cutting jig and a dado blade. This method involves no measuring and take only a minute or two. The trick is to use brass set up bars. I keep my set close to the dado saw in my shop. Hold the largest bar on a 45 degree angle on the corner of the box. Add other bars until you get a combination that is just a little under the width of the box ...
Kaj has supplied with a lot of wood to help me with my knife making and turning.This handle uses more traditional materials. He saw the knife with the Purple Heart and liked the colour.Birch Bark spacers, Thin strips of elk horn. Masur Birch for the handle. Measure, Mark, Drill, File to fit.Each piece. The masur Birch handle are 2 angled bores like—> \ |Before gluing with epoxy I layed the materials out in order of gluing. The whole process took about 2 hours.
Early on, a woodworker is forced to decide upon a sharpening system or product. And I know we have some folks on Ljs who are just entering the wonderful world of hand tools. This is my attempt to not leave those people hangin when it comes to sharpening. Clearly, planes and chisels are just handsome paperweights if they’re not sharp.Let me start by saying that I am far from an expert. Shoot I’ve only been using and sharpening hand tools effectively for about a year. I spent the pr...
This Week I show you how to make a folding out feed table for your table saw. This design was based after an article and plan found in a 2009 issue of Woodworker’s Journal Magazine. Originally the plan was designed for a Cabinet saw with a Biesemeyer Fence System, so I had to make some slight modifications for my Porter Cable Saw. In this 3 part video series I show you a step by step on building this project as well as talk about the modifications I had to make. The Article and plans ca...
So I decided to blog on the woodworkers and writers who inspire me to “work the wood” besides the fact that it is a thing that is just “in my blood” or a legal addiction…how nice! Slant Top Desk by C.H. Becksvoort The Short List Woodworkers (in influential order)1. C.H. Becksvoort-maker of amazing Shaker Style Furniture plus great Shaker Inspired Author2. Thomas Moser-the great American Dream in real life, Thomas Moser Furniture-and a great classic book ...
When building my wife’s new chest on chest cabinet, I decided to add a little something a little different than the plans that I had on hand, which would be new to me & adds a new challenge for me overcome. The basic plan for this storage cabinet came from Glenn Huey’s book “fine Furniture for a lifetime”, the Chippendale Entertainment Center. This same piece of furniture is featured in another of his book by Popular Woodworking, “Design & Build Your Ideal Entertainment Center”, and i...
Well it has been a anxious and emotional week for me and not much got done on the table but such is life.This week I played around of and on with some yellow glue and some 1/8” walnut veneer ,I rolled on glue on both surfaces (three different types seen in the pic ) and let the samples dry until clear and layed it on the plywood , put a hot iron on the veneer and heated the glue until it bonded and followed with a piece of wood to rub it flat .The result was a nice strong bond and tryin...
If anyone is looking for bandsaw blades in Phoenix, I just found a guy named Bill on Craigslist. His number is 602-266-5073 and can make a variety of blades. I am one who prefers to support the local businesses when I can. I am not incentivized by Bill to sell more blades, just thought I would pass it along. I’m going to go pickup a couple blades from him and i’ll follow up with reviews of what how they do.
THE ART OF NOT TAKING A TRIP TO THE EMERGENCY ROOM!Yesterday I awoke out of my daze of admiring a quilted maple block with a shocking sensation and blood everywhere. The dull blade on my bandsaw did not help and using my hands to push the beautiful block through didn’t help either. Simple word of advise which many of you can attest too. Keep your tools sharp and use a push stick! Lets say it all together now! Keep your tools sharp and use a push stick!Keep your tools sharp and ...
- My Journey As A Creative Designer - Woodworking and Beyond - 1806 parts
- Extremely Average - 324 parts
- Toy costruction - 126 parts
- A journey into the workshop. - 111 parts
- Workshop Development - 107 parts
- Just for Fun... - 98 parts
- Woodworking on a Half-Shoestring - 90 parts
- Daily Update - 87 parts
- Life as an Amateur Woodworker - 81 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- Sheila Landry (scrollgirl) - 1831 entries
- dbhost - 438 entries
- frank - 417 entries
- degoose - 397 entries
- Ecocandle - 325 entries
- mafe - 318 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- Martin Sojka - 296 entries
- William - 258 entries
- shipwright - 254 entries
- robscastle - 245 entries
- Dave Rutan - 245 entries
- Betsy - 228 entries
- stefang - 221 entries
- A Slice of Wood Workshop - 213 entries
- Stevinmarin - 212 entries
- Todd A. Clippinger - 207 entries
- Gary Fixler - 204 entries
- bandit571 - 201 entries