Recently Big Al, i.e. “Boxguy” posted a jig he had built for cutting accurate mitre joints. I built one this afternoon, and thought I would share my attempt at making the same jig. Total cost for the jig was around $17.00 – - the all in one clamp. The time was 2 1/2 hours. MDF remnants, left over material from other projects, and junk drawer parts finished it to this point. Still have to finish up the stop system, but was anxious to use it today, so will add the stop tom...
Cap iron or chip breaker, blade or iron – Some folks write treatises about which term is “correct”. I use the one that comes to mind, they mean the same thing. Chip Breaker Function The chip breaker adds mass to the blade and adds stiffness to the blade, and with the lever cap pushing down, seats breaker & blade flat on the frog, creating more blade stiffness (cap iron). A very important, but lesser known, function of the chip breaker is to create a force down the wood fibers as the...
This is a picture of my first test humidor, obviously it’s a work in progress. I’m using box joints like this for it, and I am using the Freud box joint table saw blade set. I chose some cheap hemlock because I was not sure how well I would do. Aside from some tear out because my table saw jig was set up ( sawn through ) for 3/4” depth of cut, and now for the build I’m using 1/2” wood and depth of cut, it didn’t come out too badly. The tear out problem was...
This countertop around oven range will be made of two separate pieces which connect through a “bridge” with one seam behind the range. The right part is about 13” x 24”, the left—37” x 24”. The bridge is of two parts, each is 40” x 3” and to be glued to either left or right side to allow one seam connection. Cut the 1-13/16” walnut boards into segments: The left side glue-up: Two boards of the right side glue-up: ...
I have been fortunate enough to assemble and use an array of handplanes – Stanley Bailey bench, block, and specific use planes, oriental woodies of various sizes, Lee Valley Veritas bevel up and scraper planes, and some other assorted types. It took a while, as in 4-5 years of using, fettling, trying various methods of things and different plane designs to form up some conclusions from my experiences. I thought I would pass along these experiences, primarily with the lesser experienced in min...
After looking through some other blogs here on LJ and watching some Youtube videos I thought that the tumbling block cutting board was something that looked challenging, cool and something I wanted to try. I learned some good ideas from these other blogs and wanted to share some of my experiences having now made three of these, my setbacks and discoveries to better produce these tumbling block patterns. I purchased a Wixey digital angle gauge as it looked like you really needed to be accu...
Here is an idea for gun owners that don’t have a gun case or space for a wall gun case. That being said it is not just for guns, you can display just anything that will fit in the case, such as coins, knick knacks, precious mementos. The dimensions are 5’ by 2’ by 18” when it will be finished. There will also be a drawer under the showcase in the center of the table. The wood used is reclaimed barn wood from my barn.
I have run all the 10/2 and 10/3 that I need except for two lines that need to be spliced. The rest of the lines are 14/2. I originally thought I could get the 8 runs to the Woodshop through a 2in conduit. But here you can see that with only the 10/3, and still needing 8- 14/2 wires, there was no way. I will have to go up to a 3 in conduit to avoid derating everything circuit! Having run over a mile of cable and wire, I have installed approximately 4 splices. I am sure I will have ...
Use up a few scraps and the rest of the 10” table saw blade for this easy made marking knife. Check the video out HERE! As always, please subscribe!
I’m looking to make a replacement blade for a hollow auger. I know the blade is one inch wide. I do not know thickness or length as the auger has not arrived yet. If anyone has one of these hollow augers, could they post a photo of the blade? Also, I would be interested to know if anyone knows of a source for these blades. I am assuming one will have to be made but it does not hurt to ask. Example of what the blade looks like.
- My Journey As A Creative Designer - Woodworking and Beyond - 1832 parts
- Extremely Average - 324 parts
- Toy costruction - 131 parts
- A journey into the workshop. - 115 parts
- Workshop Development - 107 parts
- Just for Fun... - 98 parts
- Woodworking on a Half-Shoestring - 91 parts
- Shop stuff - 89 parts
- Daily Update - 87 parts
- Life as an Amateur Woodworker - 82 parts
- Sheila Landry (scrollgirl) - 1857 entries
- dbhost - 455 entries
- frank - 417 entries
- degoose - 398 entries
- Ecocandle - 325 entries
- mafe - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- Martin Sojka - 296 entries
- Dave Rutan - 277 entries
- robscastle - 266 entries
- shipwright - 259 entries
- William - 258 entries
- A Slice of Wood Workshop - 241 entries
- bandit571 - 237 entries
- Betsy - 228 entries
- stefang - 221 entries
- Stevinmarin - 212 entries
- Todd A. Clippinger - 207 entries
- Gary Fixler - 204 entries