Forrest WWII, Infinity Super General, Ridge Carbide TS2000, Freud Fusion, and Tenryu Gold Medal are all great saw blades. It’s hard to go wrong with any of them if you’re willing to plunk down $80-$130. Try getting a good blade with a budget in the $10-$40 range, and the odds of getting a good one fall dramatically. No need to despair….for those who missed out on the great Leitz/Irwin, Leitz/Delta, Onsrud, Delta 7657, and CMT clearance deals in recent years, below is list of current deals tha...
Recently, I watched some of a woodworking video. I say some, because once I saw the presenters method for checking square on the TS, I turned it off. This is not squaring up a blade in reference to the top, it is getting square in reference to the insert. Little demonstration on how this will steer you wrong. Square, but not 90 degrees to the top. If you have a quality combination square, this is the way you square a table saw blade. It’s the way I was shown and I belie...
My Workshop Tour My workshop has two levels the ground floor where all my tools are (54m2/580ft2) and the half top floor (16m2/172ft2) which has two rooms; one is used as a paint booth and the other as a drying area as well as storage room. Entering the shop the in the center is the heart of my shop, the table saw/router table, an out-feed table serves also for assembly and in the far East wall my SCMS station. Farther in on the left there’s my dust collector and next to ...
This project was started as an alternative to a trampoline. The floor is about 8.5ft above ground on a 12ft post at the lowest point. Roughly 7’ wide by 11’ long.
Hey everyone, Just wanted to share a couple of shop Jigs with you. One is a quick and simple jig for quartering your sheets of sandpaper to use in your palm sanders or sanding blocks. The second jig is a multi function tapering Jig that lets you do 4 sided tapers as well as straight edging rough sawn boards and cutting angles also.. There could be many more uses, there are just the 3 I focus on in the videos. Part 1 Part 2 Part 3
I have a small shop and a small budget, so as I slowly grow my shop I have finally came to the topic of jointery and furniture making so I have my list narrowed down to purchasing the Incra iBox and a nice dado blade (suggestions on blades gladly appreciated) or a nice router and router table set up or keep saving up for a grizzly bandsaw. any and all suggestions welcomed
Oh yea! Time to kick off the summer with the 2nd Annual Whirligig Wars Woodworking Event. Spend that shop time preparing for battle and build a whirligig for the event. We have some great prizes this year from our Awesome Sponsors Laguna Tools Rockler Woodworking and HardwareWoodworkers Guild of AmericaMicro JigThe United Federation of Woodworkers Brought to you by A Simple Design of Ocala, Inc. & Woodworking for Mere Mortals You don’t want to miss this!! Here is a look ...
Recently I posted a video covering common woodworking joinery ( http://www.youtube.com/watch?v=zqXLYe783qw ) with the help of a few friends. In that video I talked to you all about making finger joints on the table saw and showed you a finger joint jig in the process. Well as I promised, here is the complete build process of that Jig. Table Saw Finger Joint Jig Also a little reminder about the 2nd Annual Whirligig Wars. It is almost here!! The event Runs from July 10 –...
I ask a couple of my woodworking friends to help me talk to you about some common woodworking joinery. Woodworking joinery is the method of joining two pieces of wood together to create a more complex item. Woodworking Joinery is the one thing we as woodworkers need to know and this video talks about 4 common woodworking joints that you are most likely to use in your projects. In this video you will learn about the following joints Half Lap Joints – Presented by Jay Bates Jays...
While at Mom’s the other day I salvaged an empty pill bottle (fish oil, it’s BIG) thinking “This might be big enough to put scroll saw blades in.” Brought it home and today, while waiting for finish to dry… I tried it out and with some scrap 1/8th inch plywood made the holder. Nothing fancy. I didn’t even sand it. I made a ‘collar’ that will keep the blade ends in the center of the bottle so as to not interfere with the lid and labled it with th...
- My Journey As A Creative Designer - Woodworking and Beyond - 1742 parts
- Extremely Average - 324 parts
- Workshop Development - 107 parts
- A journey into the workshop. - 106 parts
- Just for Fun... - 97 parts
- Daily Update - 87 parts
- Life as an Amateur Woodworker - 79 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 76 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- Sheila Landry (scrollgirl) - 1767 entries
- dbhost - 419 entries
- frank - 417 entries
- degoose - 397 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- mafe - 304 entries
- Martin Sojka - 296 entries
- William - 258 entries
- shipwright - 246 entries
- Betsy - 228 entries
- stefang - 220 entries
- robscastle - 218 entries
- Dave Rutan - 214 entries
- Stevinmarin - 212 entries
- Todd A. Clippinger - 207 entries
- Gary Fixler - 204 entries
- Smitty_Cabinetshop - 194 entries
- A Slice of Wood Workshop - 190 entries