I am making some podium out of solid cherry .I assembled them using mitre foods with biscuits .Tight joints when I first glued them up but a couple months later the joints are partially open , maybe 1/32nd. Any suggestions on repairing.it hasn’t been stained or finished yet.
Wood has three dimensions and the table saw cuts both X (length) and Y (width) The Z (thickness) axis needs a lunch box planer. The table saw has the Incra rip fence and miter gauge so X and Y are covered. Z however needed some help getting the same accuracy as the saw. One of the benifits of digital gauges is that I can see the reading without squinting or having to bend down. I have a digital height gauge to set the saw height and set the router bits consistently. Repeatability is...
Used to have a shop, X got in the divorce. :( Fast forward 15 years & I have 2/3 of 1/2 of a garage to build a cabinet shop in. The core of any shop is the table saw and within my (retired) spending limit I got a brand new Grizzly G0715P. Simultaneously with the saw purchase I added an Incra LS-III rip fence and an Incra miter gauge. I’m disabled and can’t walk / stand a lot so everything is within reach of my chair in front of the saw. I’ve got most all of th...
This build was a result of a challenge from another you-tuber named Opa Koster. I really liked the results and wanted to share the pictures and video here on lumberjocks. The bench was bought from a local antique store and was painted with some ugly green paint over the wood and cast iron. I had quite a task to remove that paint and primer from the cast iron. I liked the back cast iron piece but I envisioned a different project for it. So it has been saved it for a later project ...
I was eager to put my tools in the chest before sanding and finishing. I decided to use shop scraps to create holders to store my tools. I had already made crude holders for my saws, chisels, screwdrivers, rasps/files and marking tools. So I inserted these into the chest. Once in place I began to find symmetry in laying out the remaining tools. Again I used scraps to make temporary holders to organize the tools. One by one, I added a tool or group of tools and imagined how I could maxi...
There is no question about it, ‘at some point during our trek into the world of wood working we are going to need some sort of jig, whether it is a temporary one or a permanent go to Jig. Of course if you google it, you no doubt will get flooded with every type of jig imaginable, go to you tube and you find find countless video’s to build all sorts of nifty jigs. In my wood working most of my jigs are temporary jigs. Pending on what you your self are doing you may need more than o...
In this episode, I make the back from some maple stock. The back is ship lapped and will be installed in a groove in the back legs I also make a solid cherry top with a curved front. Now I will say I completely screw up the first attempt by, well just being really stupid and not paying attention to what I was doing, and using the wrong bit in my router. I do show how I recover from this mistake in the end. As always, I welcome your questions and comments! To keep up with what I’...
The time has come to start building my new workbench. I am using wood from some industrial size pallets from my work. The wood is some kind of spruce that came out of Hungary. In this installment I will be preparing the stock that will become the tabletop. I have to do some serious milling to get the stock straight and square before I could get it ready for glue-up. Be sure to participate in the comments section, and I hope you enjoy the video! View on YouTube Instagram: https://www.i...
I have never been a real believer in the use of biscuits in the glue up of large table tops or wider sections in general. Especially where end grain and long grain must be glued together. However, I have never used them either. I’m very old school and have always defaulted to Mortise and tenon and have often pinned those joints with dowels. It strong, its reliable, if time and proper procedures are used to make the joints properly. That’s the downfall this construction method i...
So after talking to the owner of the salvage store for a little while he let me go down and pick the basement where all of the items from his estate buy outs go before they put them on the sales floor. I was floored with the amount of stuff that he had down there. Picture a room the size of a football field filled with boxes, trunks, shelves and crates FILLED with amazing stuff. I picked for about 2 hours and found everything we like from vintage, rare Stanley #18 Sweetheart plane, a Stanley ...
- My Journey As A Creative Designer - Woodworking and Beyond - 1828 parts
- Extremely Average - 324 parts
- Toy costruction - 131 parts
- A journey into the workshop. - 115 parts
- Workshop Development - 107 parts
- Just for Fun... - 98 parts
- Woodworking on a Half-Shoestring - 91 parts
- Daily Update - 87 parts
- Shop stuff - 85 parts
- Life as an Amateur Woodworker - 82 parts
- Sheila Landry (scrollgirl) - 1853 entries
- dbhost - 452 entries
- frank - 417 entries
- degoose - 397 entries
- Ecocandle - 325 entries
- mafe - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- Martin Sojka - 296 entries
- Dave Rutan - 275 entries
- robscastle - 263 entries
- William - 258 entries
- shipwright - 258 entries
- A Slice of Wood Workshop - 233 entries
- bandit571 - 229 entries
- Betsy - 228 entries
- stefang - 221 entries
- Stevinmarin - 212 entries
- Todd A. Clippinger - 207 entries
- Gary Fixler - 204 entries