160 days ago
by Andy |
13 comments »
Now that everyone has their wood selected,lets get started.
Note. There will not be your typical cut list of material sizes when making this box.We will cut the box body and a dado for the bottom.The size of the bottom will be measured off of that.
We will then route out for the lid and its size will be determined from that.
Lastly, we will route the recess for the medallion and we will get our final measurement from that.
Note:Depending on your skill level and how clear my instru...
Read this entry »
159 days ago
by Andy |
17 comments »
We now have our box body assembled and glued up.Take off the tape and clean off any dried glue.This is a good time to smooth up the bottom to get rid of any rocking.You can double stick sandpaper onto a very flat and firm surface and slide the bottom across that.The problem with this approach is that sheet sandpaper is way too small.You can stick down several sheets and if you go very slow you may not tear the paper.
Tip:I designed this sanding platform for leveling boxes and flushing out ...
Read this entry »
163 days ago
by Andy |
9 comments »
Let the fun begin!
I know everyone is hoping I will just shut up and just get down to the cutting and sanding :)
BUT…..This is very important to those of you who are trying to imitate my process from beginning to end.Many of you have admitted that you have never built a box before and would like to know how to select a winning combination.So,the first bit of business is to select the wood you will be using.This decision will be based on A) what you find appealing.This is totally s...
Read this entry »
151 days ago
by Andy |
15 comments »
Three lid choices.
DO NOT CUT THE LID TO SIZE UNTIL YOU ARE SURE OF THE STYLE OF BOX YOU WANT TO MAKE!
At the start of this tutorial I mentioned that we would look at three ways to make this box.
We are at a point in the project,where we need to decide how we want our lid to open.You will need to look at each type and decide which is your favorite or the easiest for you to make.
I suggest following on with this tutorial and weighing the pros and cons of construction,before making a f...
Read this entry »
99 days ago
by Andy |
22 comments »
This box required a great deal more time and care during the final sanding,mostly in trying to maintain the edge of the ridges.At first I intended to keep them as crisp as possible…which took alot of time…but I didnt care for the look afterwards.It just looked too machine made,not as organic as like.I started out with a concept of sand dunes that I thought would tie in nicely with the grain of the Myrtlewood,but thats about it.I dont try and plan out every detail of the shaping a...
Read this entry »
152 days ago
by Andy |
4 comments »
Now that we have our lid fitted to the box,we are ready to move onto the medallion.
DO NOT CUT THE LID TO SIZE UNTIL YOU ARE SURE OF THE STYLE OF BOX YOU WANT TO MAKE!
This is where you can get creative.I wet the surface of the box with mineral spirits to get a feel for what it will look like when finished and then start laying my selections across the top.Contrast is what you are after,either in grain or color or both.
Example On Page # 1 of this series you will find a picture of Ra...
Read this entry »
155 days ago
by Andy |
9 comments »
At this point we have a box body with corner splines.Our lid is still oversized, so we can stop here and just use it to make a traditional box,one where the lid sets on top.
DO NOT CUT THE LID TO SIZE UNTIL YOU ARE SURE OF THE STYLE OF BOX YOU WANT TO MAKE!
For some, this may be the best option.They may not have all the required tools or may feel their skills need a little more honing.Or, you could leapfrog over the next few stages and pick up the project again when we do the medallion....
Read this entry »
130 days ago
by Andy |
9 comments »
This is the fun part!
Up to this point,everything we have done has been carefully layed out and measured.This phase is more free form,its where we can cut loose a little, and see what we get.But a little care must be used or we can wind up with a ruined box.That happened on occasion when I first started playing around with this concept a few years ago.Just go slow and you will be fine.
I like to mount my box to the “Moaning Stool”,to keep it from moving.This places it at a...
Read this entry »
135 days ago
by Andy |
7 comments »
The handle.
You dont really need a handle to open this box.You can just press down on the top,at the back, and the front will lift up.
But a handle keeps the finger prints down and adds to the overall design too.It can accentuate the linear flow if it is long and delicate,or it may add more of a whimsical feel to the box if it is stubby and rounded.And it is a visual tie-in to the medallion if they are made from the same wood.
For this box, we are going to make a handle, and cut out ...
Read this entry »
37 days ago
by OregonBurls |
21 comments »
Hey everyone,
I was asked by a few of you from my blog “How to find legal burls” “once I get them how do I cut the burls”?
Well I just made a short vidio on how I cut to the burl in the context of a bowl or hollow form blank.
Please coment and add if I don’t cover it well. If you not want to go thru the hassle of finding and cutting your own you can alway buy from me. LOLThanksGreg
Thanks Todd on the tip for getting the video on this post.
Read this entry »
1 2 3 4 ... 14
132 entries
