106 days ago
by degoose |
28 comments »
Hi guys ,, I had a request to make a tutorial with regards the endgrain Tumbling Block Design.First off,.., You need to decide the size of the blocks…. for this example I used 1” stock… Or something similar.. actually just over .. once dressed.
Set the blade of the table saw to 60 degrees.. a bevel box makes this simpleI use the INCRA fence system so it is easy to rip bevels off side of the blade.Once the bevels are ripped measure the length of the bevel and move the f...
Read this entry »
157 days ago
by Andy |
13 comments »
Now that everyone has their wood selected,lets get started.
Note. There will not be your typical cut list of material sizes when making this box.We will cut the box body and a dado for the bottom.The size of the bottom will be measured off of that.
We will then route out for the lid and its size will be determined from that.
Lastly, we will route the recess for the medallion and we will get our final measurement from that.
Note:Depending on your skill level and how clear my instru...
Read this entry »
156 days ago
by Andy |
17 comments »
We now have our box body assembled and glued up.Take off the tape and clean off any dried glue.This is a good time to smooth up the bottom to get rid of any rocking.You can double stick sandpaper onto a very flat and firm surface and slide the bottom across that.The problem with this approach is that sheet sandpaper is way too small.You can stick down several sheets and if you go very slow you may not tear the paper.
Tip:I designed this sanding platform for leveling boxes and flushing out ...
Read this entry »
160 days ago
by Andy |
9 comments »
Let the fun begin!
I know everyone is hoping I will just shut up and just get down to the cutting and sanding :)
BUT…..This is very important to those of you who are trying to imitate my process from beginning to end.Many of you have admitted that you have never built a box before and would like to know how to select a winning combination.So,the first bit of business is to select the wood you will be using.This decision will be based on A) what you find appealing.This is totally s...
Read this entry »
148 days ago
by Andy |
15 comments »
Three lid choices.
DO NOT CUT THE LID TO SIZE UNTIL YOU ARE SURE OF THE STYLE OF BOX YOU WANT TO MAKE!
At the start of this tutorial I mentioned that we would look at three ways to make this box.
We are at a point in the project,where we need to decide how we want our lid to open.You will need to look at each type and decide which is your favorite or the easiest for you to make.
I suggest following on with this tutorial and weighing the pros and cons of construction,before making a f...
Read this entry »
96 days ago
by Andy |
22 comments »
This box required a great deal more time and care during the final sanding,mostly in trying to maintain the edge of the ridges.At first I intended to keep them as crisp as possible…which took alot of time…but I didnt care for the look afterwards.It just looked too machine made,not as organic as like.I started out with a concept of sand dunes that I thought would tie in nicely with the grain of the Myrtlewood,but thats about it.I dont try and plan out every detail of the shaping a...
Read this entry »
149 days ago
by Andy |
4 comments »
Now that we have our lid fitted to the box,we are ready to move onto the medallion.
DO NOT CUT THE LID TO SIZE UNTIL YOU ARE SURE OF THE STYLE OF BOX YOU WANT TO MAKE!
This is where you can get creative.I wet the surface of the box with mineral spirits to get a feel for what it will look like when finished and then start laying my selections across the top.Contrast is what you are after,either in grain or color or both.
Example On Page # 1 of this series you will find a picture of Ra...
Read this entry »
152 days ago
by Andy |
9 comments »
At this point we have a box body with corner splines.Our lid is still oversized, so we can stop here and just use it to make a traditional box,one where the lid sets on top.
DO NOT CUT THE LID TO SIZE UNTIL YOU ARE SURE OF THE STYLE OF BOX YOU WANT TO MAKE!
For some, this may be the best option.They may not have all the required tools or may feel their skills need a little more honing.Or, you could leapfrog over the next few stages and pick up the project again when we do the medallion....
Read this entry »
75 days ago
by degoose |
24 comments »
This board is not part of the 150.. I showed one of the 150 to a friend and she wanted one but a little larger,This is the way it was made.Cut some bits of board. NGR SA TBDress all sides.This is to see the way it will look with the stripe. Cut all pieces to 250 mm.Join the NGR and edge with TB on one and SA for the other.Glue a sacrificial board to the SA prior to cutting the arcs.This is the arc cutting jig.. a slight variation on the patron jigSet the stop with a nail… high tech I kn...
Read this entry »
185 days ago
by Andy |
168 comments »
I am sure most of you that have seen my Art Boxes have read my comments,tips and my lengthy answers explaining my process.So…I am thinking that many of you probably have enough information to make your own box without further help from me.But maybe not.What I would like to know is how many Jockeys out there would like me to do a tutorial,step by step,on a new box? With lots of clear photographs?
I have to be honest here,its alot of work to do a good job on this and my time could be s...
Read this entry »
1 2 3 4 ... 56
557 entries
