Recently I posted a video covering common woodworking joinery ( http://www.youtube.com/watch?v=zqXLYe783qw ) with the help of a few friends. In that video I talked to you all about making finger joints on the table saw and showed you a finger joint jig in the process. Well as I promised, here is the complete build process of that Jig. Table Saw Finger Joint Jig Also a little reminder about the 2nd Annual Whirligig Wars. It is almost here!! The event Runs from July 10 –...
I ask a couple of my woodworking friends to help me talk to you about some common woodworking joinery. Woodworking joinery is the method of joining two pieces of wood together to create a more complex item. Woodworking Joinery is the one thing we as woodworkers need to know and this video talks about 4 common woodworking joints that you are most likely to use in your projects. In this video you will learn about the following joints Half Lap Joints – Presented by Jay Bates Jays...
This week’s Project is a horizontal Murphy Bed. The bed I built is a twin size bed using the Create-A-Bed Hardware kit from Rockler Woodworking and Supply. The finished look of the bed can be trimmed and finished to match your homes decor, really the limit on the final look is only limited by your imagination. These videos just tell you about the use of the hardware kit and the general construction of the project. I hope you enjoy it.
It’s that time of year once again. The 2nd Annual Whirligig Wars event is approaching! Woodworkers around the globe are beginning to construct their whimsical whirligigs with the hope of winning one of the great prizes this year. Whirligig Wars came to life last year when woodworkers across the globe battled it out and waged a war in wood. Due to it’s success Whirligig Wars has gained recognition from woodworkers and woodworking enthusiasts across the globe. In the Summer...
:O) I am a bit excited. I finally have a set of GRR-Rippers in the shop. I have been wanting one for a long time. So I put together this video to show you just a couple reasons why I am pumped up about these helpful shop accessories. Not only are they keeping me safe, but they are allowing me the opportunity to perform tasks I couldn’t perform before… That in itself has got me doing backflips… lol Here is a look at the video
When a viewer sent me a comment asking if I could make a First Aid Cabinet for the workshop, I thought to myself. “Yea what a perfect project to do”, because I am setting up the new shop, and it was the one thing missing. The First aid Cabinet was made almost entirely out of Pallet Wood. Oh yea! my first Pallet Project! http://www.asimpledesignofocala.com – Websitehttp://www.ufoww.com – The United Federation of Woodworkers Member Sitehttp://www.twitter...
Quartersawn oak blanks are cut to 14” long and 1 5/8” thick. The upper crest rails are 3” wide and the lower rails are 2 ½” wide. I chose to construct the chair with floating tenons so that I could mill and cut all of the rails to the exact same length. A bench-top mortising machine is used to make the mortises for the upper and lower crest rails. The 3/8” chisel is set exactly parallel to the machine’s fence, then an auxiliary fence is installed and shimmed to the proper angle required. Sto...
The one Project Video I get asked the most to make is how to build a crosscut sled for the Tablesaw. Well there are a lot of videos out there on making a Cross cut sled, so this is my take on it. I hope you can take something from this video and use it in your shop
Well I finally finished the Tablesaw Base, trying to film during rain storms is almost impossible with the ambient noise from the rain hitting the metal roof.. but I waited it out, and am very happy with the outcome.. Here is a look at the final steps of building this base
Recently I had a need to build a new table saw base for my saw. Rather than just building a simple replacement base, I opted to build one with lots of storage potential. This new base measures 6 feet long by 2 feet wide, which gave me good reason to move over to the new shop building. I haven’t yet finished the new shop set up ( haven’t even started) but this build is a great start giving me lots of options for storage potential… This build is a 2 part project. So be sure to...
- My Journey As A Scroll Saw Pattern Designer - 1598 parts
- Extremely Average - 324 parts
- Workshop Development - 107 parts
- Just for Fun... - 96 parts
- A journey into the workshop. - 89 parts
- Daily Update - 87 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 76 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- ScrollSaw Information and Resources - 68 parts
- Sheila Landry (scrollgirl) - 1623 entries
- frank - 417 entries
- degoose - 397 entries
- dbhost - 390 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- Martin Sojka - 296 entries
- mafe - 279 entries
- William - 258 entries
- Betsy - 221 entries
- shipwright - 218 entries
- Stevinmarin - 212 entries
- Gary Fixler - 204 entries
- Todd A. Clippinger - 199 entries
- stefang - 198 entries
- Rustic - 188 entries
- BritBoxmaker - 187 entries
- Chris Davis - 183 entries
- Smitty_Cabinetshop - 176 entries