LumberJocks

Woodworking blog entries tagged with '407'

  • Advertise with us
View Ryan Haasen's profile

Model Bell 407 helicopter project #8: Tail boom attached and the beginning of the engine housing.

04-11-2012 02:45 AM by Ryan Haasen | 5 comments »

Over the past few days it has started to take the shape of a helicopter. Here is the switch panel located on the roof of the cockpit (sorry for the poor quality of the image): This is a photo of clamping on the tail boom. Every minute the clamp stayed on there I worried that something on the body would give, but I was lucky and all went well. Today I just began the engine housing, it is coming together well. There a lot more to do but I am happy with it so far. Although there is ...

Read this entry »


View Ryan Haasen's profile

Model Bell 407 helicopter project #7: Rotor blades and progress on the interior.

04-09-2012 03:09 AM by Ryan Haasen | 3 comments »

The past couple of days I have been working hard to make progress on the helicopter. In the past two days I have make the anti-tourque peddles, more details in the interior, and finished the the rotor blades along with attatching them to the rotor head. Here are the anti-tourque peddles,every part is walnut and the peddles were turned on the lathe: In the interior I added the instrument panel, the cyclic control, a bunch of switches on the roof of the cockpit (which you can not see ...

Read this entry »


View Ryan Haasen's profile

Model Bell 407 helicopter project #5: Cutting the body open.

03-16-2012 02:57 AM by Ryan Haasen | 4 comments »

So fo the past while I have been sanding the body to shape. I was also doing anything I could to avoid facing the challenge of cutting the body apart. I was afraid of doing so because it is not a cheap chunk of wood, and also all the effort put into getting the shape correct shape made it more special. Then one day I decided it had to be done and I did it. And that new bandsaw got quite the workout. It did go better then I expected with the minor flaw here and there. after the walls were ...

Read this entry »


View Ryan Haasen's profile

Model Bell 407 helicopter project #4: Sanding and shaping.

02-07-2012 04:51 AM by Ryan Haasen | 2 comments »

In the last while, I have been sanding and shaping the helicopter. I did end up getting the pneumatic sander. It is the perfect tool for the job. I have probably spent 10 hours, but many more are to come. It is ver difficult to get it to the same shape of the real helicopter, it is still more square-ish then I would like it to be. Also just realized that the rear-bottom comes to a point, so a lot of material is yet to be removed. Thanks in advance for your comments.

Read this entry »


View Ryan Haasen's profile

Model Bell 407 helicopter project #3: Seats and rotor head.

01-16-2012 12:02 AM by Ryan Haasen | 9 comments »

Its about time to give you guys an update. I have finished the rotor head. It has almost all the same parts as the real ones, and moves in all directions (both collective and cyclic movement). I also cut the size of the main rotor blades, which are wenge. At first, the rotor head could not take the weight of the blades, so extra supports were added. The rotor head is maple and the dish on top is cherry. I also began working on the seats. I have the middle row done. They are cherry, padauk...

Read this entry »


View Ryan Haasen's profile

Model Bell 407 helicopter project #2: Cutting Out The Basic Shape.

01-08-2012 10:07 PM by Ryan Haasen | 5 comments »

Today was the big day; cutting out the basic shape of the helicopter. I did it like you would do those scroll saw or bandsaw reindeer (cutting out two perspectives to get a final shape in the middle). I have to admit that this morning before I started I was nervous because I had never cut anything so big on the bandsaw, and messing up would be costly. The blank for the body of the copter weighed 30lbs, and was difficult to manuver around the bandsaw, even when I was constantly lub...

Read this entry »


View Ryan Haasen's profile

Model Bell 407 helicopter project #1: Ready to build!

01-08-2012 08:36 AM by Ryan Haasen | 3 comments »

My Dad and I made a trip to the Black Forest Company today and picked up the supplies for the helicopter project. The body will be out of cherry, the main rotors will be wenge and other details will be other exotic woods such as padauk and yellowheart. This evening I laminated the sheets of cherry into a 7” by 7” by 27” (length) blank. Tomorrow the new bandsaw is going to get quite the work out cutting this baby out. Hopefully all goes well.

Read this entry »



DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase