LumberJocks

Toninho's Favorites

  • Advertise with us
View Sheila Landry (scrollgirl)'s profile

My Journey As A Scroll Saw Pattern Designer #1145: Black Beauty

10-05-2013 10:38 AM by Sheila Landry (scrollgirl) | 31 comments »

I know . . . I am a spoiled brat! At least I feel that way this morning. How can I not when I am so fortunate to now own a “Special Edition” of the FINEST scroll saws made? Oh – and it is actually PRETTY as well! After all, for someone like me who’s other job is an artist, it is an extra bonus to have such a fine piece of machinery color coordinate with the rest of the house. Especially since it sits in the corner of my kitchen. Ah . . . but now I am sounding lik...

Read this entry »


View KoryK's profile

Intarsia Basics #3: Let’s Do Some Cutting!

04-19-2012 02:25 AM by KoryK | 9 comments »

Thanks for joining us for the third installment of “Intarsia Basics” and this is where it starts to get really fun. Cutting out the pattern is one of the best parts of doing this kind of art. It takes a little practice to get used to using your saw. You can look up some practice patterns or just make some zig zags, loop the loops, straight lines, gentle curves, and circles on a piece of paper and glue to a practice board. Cut out some of these and you will start getting used to the “feel ...

Read this entry »


View revieck's profile

Oneida's Dust Deputy D.I.Y. System.

04-19-2013 01:38 AM by revieck | 6 comments »

Building a dust collection system using Oneida’s D.I.Y. cyclone.

Read this entry »


View MichaelAgate's profile

Scroll Saw Portraits - HOW TO #2: Part 2 - Full Non Video Tutorial with screen shots.

01-27-2013 06:19 AM by MichaelAgate | 16 comments »

Hi everyone, Not sure if you seen my previous message about the video. The quality was just so bad, I couldn’t post it. The resolution was set too low. What I have below, is a tutorial on how to create your patterns. I made the tutorial as simple as possible by showing you what to push and click. I didn’t spend any time in explaining the program or any real features. My goal was to give you something that you can follow by simply following the instructions. This tutorial should...

Read this entry »


View TripleB's profile

Scroll Saw Forum #5: How To Align Your Scroll Saw Blade (Video)

02-06-2013 04:29 AM by TripleB | 7 comments »

Had a discussion with a friend today about easy ways to align your scroll saw blade to the table. Surprisingly, It was a lot more difficult to explain than I thought it would be, so I figured I’d just make a quick video and show the process instead. This process is nothing new, but I’m sure there are a few out there that might not know how to do it this way so I wanted to show you as well, just in case! BobScroll Saw Forum

Read this entry »


View Bob Simmons's profile

Parquetry #2: Hardwood Veneer Sheets of Parquetry

08-11-2012 04:02 PM by Bob Simmons | 9 comments »

More related woodworking videos & articles… Wooden Patterns for Parquetry Wood Inlay Banding – How to Make the Square Pattern Ripping Thin Strips of Wood Inlay on the Band Saw Let’s Install Wood Inlay Bandings Making Wood Inlay on the Bandsaw Creating your own Wood Inlay Bandings…The Secrets Revealed Cutting Thin Strips on the Band Saw Wood Inlay Banding – Diamond Pattern... The Apprentice and The JourneymanLearn more, Experience more!

Read this entry »


View thewoodwhisperer's profile

How I Clean My Blades & Bits

08-03-2012 03:33 PM by thewoodwhisperer | 29 comments »

If you find that your blades and bits just aren’t performing like they used to, you might not need to send them out for a sharpening. They might just be in desperate need of a good cleaning. Over time, pitch and resin builds up on cutting surfaces and causes them to cut less effectively. If the buildup isn’t removed, the increased friction and heat will accelerate the dulling of the edge and eventually the blade or bit will be toast. Cleaning AgentsThe cleaning agent I use i...

Read this entry »


View MrRon's profile

The Dynamics of Power Saws and Blades

08-03-2012 09:25 PM by MrRon | 6 comments »

Concerns regarding saw cutting accuracy usually puts the blame on the blade. Blades can cost anywhere from less than $5 to well past $100. One might think that the more expensive blade will cut better than a cheap blade. This is true up to a point. The quality of any circular saw blade will vary by manufacturer. Some manufacturers make blades with other company’s names on them. Others make them exclusively under their own name. These latter manufacturers usually are in the upper range of qual...

Read this entry »


View Bob Simmons's profile

Creating Wood Inlay Bandings...A Step by Step Process #6: Learn how to make Wood Inlay Bandings

05-01-2012 12:00 AM by Bob Simmons | 18 comments »

Taken from original article…Learn how to make Wood Inlay Bandings Visit…TheApprenticeandTheJourneyman.com Learn more, Experience more!

Read this entry »


View Stevinmarin's profile

Sawhorses

04-27-2012 04:10 PM by Stevinmarin | 16 comments »

Here’s a really simple, but sturdy pair.

Read this entry »


1 2 next »
20 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase