LumberJocks

Help

  • Advertise with us
Blog entry by Orly posted 04-13-2008 08:12 PM 5367 reads 0 times favorited 6 comments Add to Favorites Watch

I’m looking for plans for a workbench that I can set my 10” table saw in and a router table all incorporated into the table top. Please Help!

-- Orly Wooldridge



6 comments so far

View doyoulikegumwood's profile

doyoulikegumwood

384 posts in 3458 days


#1 posted 04-13-2008 08:23 PM

the new yankee workshop has a set of plans you could adapt

-- I buy tools so i can make more money,so ican buy more tools so I can work more, to make more money, so I can buy more tool, so I can work more

View smitty1's profile

smitty1

33 posts in 3165 days


#2 posted 04-13-2008 08:39 PM

Here’s Two possibilities
http://christophermerrill.net/ww/plans/UTS/ToolStand1.html

http://store.woodstore.net/mosaroce.html

Both can be adapted to fit your needs.
Smitty

-- Smitty, Alabama, http://www.firstdesignwoodworking.com/

View Harold's profile

Harold

310 posts in 3314 days


#3 posted 04-13-2008 09:18 PM

Good question! hey I would also like something similar. I like the two designs that were posted, but how about something with alittle more table on the outfeed side. Orly, what I was thinking is something that could also serve as an assembly table/workspace if needed, a table that will basically take up an 6’x4’ area. I do like the one design that incorperates the fence for both router and tablesaw.

-- If knowledge is not shared, it is forgotten.

View Orly's profile

Orly

6 posts in 3161 days


#4 posted 04-13-2008 11:41 PM

Thanks guys! I be back later with what I find. Great site!

-- Orly Wooldridge

View Lip's profile

Lip

158 posts in 3516 days


#5 posted 04-15-2008 08:52 AM

Before the wife kicked me out of the garage … my setup was based on this ... with a few alterations … one being the pivot-out table saw module ... rather than attaching it to the main bench as the plans call for I made it a stand alone table that measured roughly 71” ... or about the same length as the mobile table Smitty posted from the Wood store … I’d post pictures of it, but I sold it off with the table saw since that was much easier than trying to figure out how to get it down into the basement …

This is a rough idea of what I did to give you an idea of how I modified their plan … I didn’t add the wheels to the drawing but it had a total of six wheels … one under each of the 2X4 legs … the doors on the ends weren’t anything fancy … frames were made out of 1X2 with a pegboard panels and mounted with a piano hinge … and the out feed table folded down for storage …

Photobucket

Photobucket

Photobucket

The out feed table was OK … I never really used it for anything other than the out feed support …

Photobucket

I added the notes on the last slide because if there is one thing I miss about that table .., it was the fact that one power cord is all I ever really had to deal with … sorry for not putting up all the dimensions … but I’m not sure how much good they would do you since the whole thing depends on the actual dimensions of your table saw … if you want the Sketch Up file … so you can play with it … or so you can get the dimensions … feel free to drop me a line … and I’ll e-mail it to you or something

-- Lip's Dysfuncational Firewood Farm, South Bend, IN

View joey's profile

joey

396 posts in 3370 days


#6 posted 04-17-2008 03:38 PM

I fashioned mine after one I saw in shopnotes vol 15 issue 89, it works really well if you have a contractor saw. I know you can find it on line, but if you can’t and you are interested send me a message and I’ll send you the pdf of the plan for saw center. lots of luck

-- Joey~~Sabina, Ohio http://sleepydogwoodworking.blogspot.com/

Have your say...

You must be signed in to post the comments.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com