LumberJocks

Quick Tip #8: Work Holding Part 2

  • Advertise with us
Blog entry by Kent Shepherd posted 10-03-2016 09:17 PM 546 reads 1 time favorited 3 comments Add to Favorites Watch
« Part 7: Work Holding Part 1 Part 8 of Quick Tip series Part 9: Work Holding Part 3 »

Last time I promised to show how I use a router for T-bolts, a very important part of my work holding methods. Since there are several different methods, your choice will be determined by both your equipment and your personal preference. I find I don’t do this the same way every time, basically because I live in a perpetual state of confusion. Actually, my methods are usually determined by several factors–like how many am I doing, what size are the pieces, or maybe even which of my tools are free at the moment. Unfortunately, some of my methods are not available to everyone. However, you may find them interesting anyway.

As I prepared for this blog, I discovered the method that most of you can do turned out to be the most logical way to do just a few slots. This method is not restricted to just slots for T-bolts either. I use a lot of slots for my jigs. For this you need a plunge router with an edge guide.

I laid out pencil lines to mark the ends of my slots. Usually the length of the slots are not critical so you can eyeball that as you route. Set the plunge depth to just over the thickness of your material. Be sure to clamp on top of a sacrificial board so you don’t ruin your workbench. For safety and convenience, do not attempt with out clamping. You cannot control the router with one hand. I like to do this in multiple passes. It is safer and does a better job. This is very basic for using a plunge router. Be sure and hold the edge guide firmly against the work piece. I know some of this I information is a bit basic, but I want anyone to be able to do this no matter what there experience level is.

This is what you end up with. This slot is done with a 3/8″ straight router bit. Then I changed to a 1/2″ bit to router the other side for the T-bolt head. Flip the work piece, clamp the piece and with the edge guide in the same position and referenced off the same edge route just deeper than the thickness of the bolt head.


I also use my router table for this application. I use the Woodpecker Sidewinder router lift. Unfortunately it has been discontinued. I choose it because you can raise the bit through the work piece with it in position. JessEm Tools makes a lift you can raise from the side, available from Woodcraft. I am not sure if anyone else does at this point. I used to have to drill a hole at the beginning of the slot and position over the router bit to start the slot.

With the bit running I can raise it with the side crank through the piece. Be very aware of the bit position and keep your hands away. The feather board helps maintain control as the bit plunges from the bottom. This method is similar to the first in principal. I frequently use a sled for very small pieces which I will cover in a later blog.

I use my Torque Work Center often for this, but since there are so few of these machines in the US, I won’t go into detail for this method. You can see this machine in some of my previous blogs.

And finally, you can just drill a series of overlapping holes with a drill press and clean out with a chisel, rasp, or file. Of course this is my least favorite method for obvious reasons! I did not show this because it seemed like too much work, although I have actually done this in the past.

I hope you find this informative and as always, let me know if you have questions.

I intend on doing a video soon to cover this more in depth if anyone is interested.

-- http://shepherdtoolandsupply.com/



3 comments so far

View degoose's profile

degoose

7196 posts in 2821 days


#1 posted 10-03-2016 09:38 PM

Very informative.

-- Drink twice... and don't bother to cut... @ lazylarrywoodworks.com.au For lovers of all things timber...

View Joe Lyddon's profile

Joe Lyddon

9451 posts in 3519 days


#2 posted 10-04-2016 01:05 AM

Very good tips!

Thank you!

-- Have Fun! Joe Lyddon - Alta Loma, CA USA - Home: http://www.WoodworkStuff.net ... My Small Gallery: http://www.ncwoodworker.net/pp/showgallery.php?ppuser=1389&cat=500"

View mafe's profile

mafe

11172 posts in 2556 days


#3 posted 10-10-2016 09:53 PM

Thanks for letting us in.
Always a joy to follow how others do things and it always makes one think – hmmmmmmmmmmmmmm.
Smiles.
Mads

-- MAD F, the fanatical rhykenologist and vintage architect. Democraticwoodworking.

Have your say...

You must be signed in to post the comments.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com