LumberJocks

Ken90712's Favorites

  • Advertise with us
View JL7's profile

Another End Grain Board Build.....

09-15-2013 02:19 AM by JL7 | 37 comments »

I’ve seen people posting boards with diamonds and thought that was cool…..I built a diamond board a few weeks ago HERE... and I just finished this one today: So this blogs covers today’s board… For a change, I started with some nice wide timber. No scraps in this board. This is Yellowheart and Tigerwood: Cut into 1.5” by 26” strips (but I should have made them a bit longer). I don’t plan real well on the front end….4 of each ...

Read this entry »


View shipwright's profile

Easy. Elegant Wooden Box Hinge #1: I could kick myself

06-23-2011 07:26 AM by shipwright | 61 comments »

A few months ago I spent many many hours trying to perfectly align a set of “box joint hinges” for my project ” A Little Cabinetree” After I finally got them working I installed them on the edges of the MDF sides and doors and then veneered over the whole works. The only good part was that there were enough left over prototype parts that I could make a hinge for my next project from the cast-offs Then this week I was making a tea box for a friend and when...

Read this entry »


View SASmith               's profile

2nd Generation Chevron how to pictorial

11-20-2011 09:34 PM by SASmith | 9 comments »

I have had several LJs ask for a blog on this subject. Cut 30 degree strips to make a typical chevron Glue applied. The clamps have not been applied yet in the above picture.Draw 2 lines from like points to find the “D” point. Rough “A” points shown but will not be used in this pattern.Cut through “D” at 45 degreesThe 2nd generation emerging. My typical gluing set-up. Top and bottom cauls to keep the board flat. Plus cauls to apply even pressur...

Read this entry »


View ic3ss's profile

Jointer cutter head lock mod #1: Modify cutter head so it can be locked when adjusting knives

05-21-2012 04:53 AM by ic3ss | 2 comments »

Well I’ve had this old jointer for a little over a year now and have had to pull the knives for sharpening a couple of times already because of damaged edges. I have to be more careful I guess. I’ve read all about how to adjust the knives, it’s really pretty simple concept but it’s not that easy sometimes to get the damn things even from one end to the other, and all three knives the same. The main problems I’ve identified are these: Moving a dial indicator ar...

Read this entry »


View BritBoxmaker's profile

Impossible II

08-03-2010 06:39 PM by BritBoxmaker | 23 comments »

Hi everyone. Here is the method for making the Impossible II. Before we start I didn’t take any photos during the build for this one. I needed to concentrate full time on it and taking pics can be distracting. The CAD drawings provided here should do the job . I’ve seen Steve (spalm) use this sort of thing to great effect. I’m not giving exact sizes, you can scale things off of the pics. This will give you the angles too, mostly 60°. First the complete pattern You ...

Read this entry »


View Lenny's profile

Ribbon and Bow Box Techniques

03-19-2013 03:30 PM by Lenny | 25 comments »

Enough people have asked me how the Bow Boxes I made and posted were crafted that I figured a blog was warranted. My post is here “Bow Box”: http://lumberjocks.com/projects/68845. I have seen others make the boxes and thought you might like to see different interpretations of them. bigogre has done several. Here is one of his: “Box”: http://lumberjocks.com/projects/73998. moonls recently posted one with wonderful banding in the ribbons and bow. See it “here...

Read this entry »


View Boxguy's profile

Boxland: Work Stations and Boxing Tips #5: Mortising Piano Hinges In a Box (An Easy Method)

05-31-2012 03:07 AM by Boxguy | 16 comments »

Overview: In the last blog I detailed how to separate the top from the box and how to start with a long piano hinge then size, cut, polish, round, crimp, smooth, and paint the hinge so it will fit any size of box. In this chapter I will explain how to install a piano hinge in a box. We will go through how to mortise, fit and fasten the hinge. The essential tools are: router table, small try square, vix bit, drill and impact driver. If all goes well, it should look like this when you ar...

Read this entry »


View JL7's profile

Workbench Build #15: 3 Way Mitered Cube - the Cabinets

01-23-2012 03:42 AM by JL7 | 14 comments »

08/19/2012 Edit: Just to avoid any confusion – I didn’t end up using this concept for the bench storage…..the actual storage post follows this one…...Some day these pieces will be finished into something…...maybe. Jeff So today I started on the under bench cabinets – this starting point is sort of inspired by superdav’s post here. I like the cube design….....but wanted to make it different somehow… I remembered reading about a...

Read this entry »


View WoodJediNTraining's profile

Router Table Trivets and the Jig to make them

12-13-2012 08:53 AM by WoodJediNTraining | 14 comments »

This weeks I show how to make some decorative trivets on a router table as well as Show you how to build a jig to make them .

Read this entry »


View Bob Simmons's profile

Creating Wood Inlay Bandings...A Step by Step Process #13: Wood Inlay Banding Made Easy

11-30-2012 03:27 PM by Bob Simmons | 11 comments »

How to make wood inlay banding the easy way. This YouTube woodworking video focuses on a simple way to make an elegant & decorative wood inlay banding of maple & walnut. The two contrasting hardwoods create a striking design that can be inlaid into furniture, jewelry boxes, pictures frames, and much, much more. Beginning woodworkers as well as experienced craftsmen can watch the video and quickly learn how wood inlay banding can be easily made on the band saw. The technique for ...

Read this entry »


« prev 1 2 3 4 5 6 next »
54 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com