LumberJocks

KYJeepGuy's Favorites

  • Advertise with us
View TechRedneck's profile

Delta 50-760 with Cyclone Retrofit.

04-29-2012 11:46 PM by TechRedneck | 21 comments »

I have declared war on dust in the shop. My shop is in the basement/garage and I have been spending more and more time there. Recently I was planing/jointing around 100’ of rough cut cherry for a project which produced a lot of sawdust from all the power tools used. As a hybrid woodworker, I like to get my wood from the mill and prep it myself, saving money. Once I get the stock flat and square and within 1/8” or less then I switch to hand tools. I purchased a Delta 50-76...

Read this entry »


View Jim Rowe's profile

Thickness Sander from an 8 x 4 sheet of plywood

03-21-2013 04:46 PM by Jim Rowe | 15 comments »

This is my first attempt at blogging but I thought people might be interested in the approach I took. Getting hold of consistently dimensioned timber for making boxes has always been a challenge, especially when small thicknesses are required and when the timber is hard to come by (expensive and scarce). I have seen many examples of beautiful boxes here on LJs from makers who have either made their own thickness sanders or have bought commercial equipment. For me, buying a ready made thick...

Read this entry »


View Woodhacker's profile

Hand Cut Double Dovetail Experiment

07-03-2008 06:48 AM by Woodhacker | 74 comments »

After admiring the double and double-double dovetail joints that are capable with the Incra and other jigs, I started thinking, “Why not try this by hand?” So this box is my first experiment with handcut double dovetails. It took me some time to figure out the joinery process, but once I realized a few things about this type of joint, it seemed do-able. It was quite challenging but also a ton of fun. It also does take some degree of patience and precision…which I’m still working on. In...

Read this entry »


View degoose's profile

How to make a endgrain tumbling block butcher block board!

08-12-2009 12:13 PM by degoose | 50 comments »

Hi guys ,, I had a request to make a tutorial with regards the endgrain Tumbling Block Design.First off,.., You need to decide the size of the blocks…. for this example I used 1” stock… Or something similar.. actually just over .. once dressed. Set the blade of the table saw to 60 degrees.. a bevel box makes this simpleI use the INCRA fence system so it is easy to rip bevels off side of the blade.Once the bevels are ripped measure the length of the bevel and move the f...

Read this entry »


View RetiredCoastie's profile

My attempt at a 3D cutting #1: 3D Cutting Board Inspired by SPALM!

01-13-2012 11:14 PM by RetiredCoastie | 21 comments »

Quite awhile ago SPALM posted his project for a 3D cutting board: http://lumberjocks.com/SPalm/blog/17488 the more I followed his progress the more I wanted to build one myself and thanks to SPALM’s ripping jig and his idea I began building. Along the way I found myself in need of various clamping jigs that would make this project as easy and as accurate as possible. The journey begins:I built the ripping jig that Spalm built and ripped my stock with the blade set at 30 deg. using sc...

Read this entry »


View degoose's profile

Spirals #1: How to make the "Spiral Lazy Larry"

06-01-2009 06:52 AM by degoose | 23 comments »

You will need 12 pieces of timber roughly 5’’ by 12’’ whatever thickness you want. [ I milled mine to 5/8”]The first one I made was PH and SA—6 of each.Place timber in the jig and cut the first arc.Move the piece into the fence, clamp and make the second arc cut. Repeat 12 times.Glue it up and cut it into a circle.Put on a little tung oil finishThats about It.

Read this entry »


View poroskywood's profile

Drunken Cutting Boards #1: Drunken Alice in Wonderland Cutting Board

09-10-2009 03:22 AM by poroskywood | 42 comments »

Hey everybody, after a few personal messages here is my version of a how to on a Drunken Checker Board. I of coarse bow to the Chairman of the Board and pay tribute with beer. This is a Off-Checker pattern I call “Drunken Alice in Wonderland” The “serendipitous” nature of this piece is appealing in a far out sort of way. Here Goes… So first I prepare the Material. I am using Hard Maple and Walnut both are surfaced flat and cut 1” x 9” x 14&...

Read this entry »


View SimonSKL's profile

Making a dust hood for my Ridgid oscillating sander

01-12-2010 05:50 PM by SimonSKL | 17 comments »

After reading many favorable reviews of the Ridgid oscillating sander (model # EB44242) and with a 15% rebate offered by the manufacturer, I finally bought this sander as my Christmas present. The more I use it the more I like the sander. I would have given it a 5 star rating if it has better dust collection capability when the belt sander is used. The dust just got collected at the end of the belt and landed all over the floor. I thought there must be a better way to collect the dust. Here i...

Read this entry »


View Sailor's profile

How To make Easy Drawers

12-30-2011 05:52 PM by Sailor | 4 comments »

I just finished making some drawers for two vanities that I am building and I figured I would make a video of the easy method I use to make them. I noticed that there wasn’t a video on Youtube of how to make “easy” drawers with simple joinery so I thought I’d throw mine on there. I don’t use the best joinery I know, but it’s simple and can be done by pretty much anyone with limited tools. I have several drawers in my shop that were built this way and...

Read this entry »


View Sailor's profile

My Drawer Storage Unit

02-10-2012 03:11 AM by Sailor | 5 comments »

I just did another video on my drawer storage unit in my shop. I figured I would share it with everyone! Thanks for watching!

Read this entry »


1 2 3 next »
25 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase