LumberJocks

KTMM (Krunkthemadman) aka. Lucas Crenshaw's Forum Topics

  • Advertise with us
View KTMM (Krunkthemadman) aka. Lucas Crenshaw's:homeworkshopprojects (7)blog (27)reviews (2)forum topics (13)buddies (42)favorites (4)activity logWatch
174 days ago

Half inch brad point drill bit to the hand..... (graphic image) - 23 replies

I was working on my grandfather’s deck. We were missing some fasteners the other day so we had not yet bolted in the ground anchors. These anchors are under the deck and in an inconvenient spot. While under the deck I was drilling the holes for the supporting boards when the drill snagged at the same time it broke through the other side...

187 days ago

Flexcut Whittlin Jack and Sheath - 0 replies

I have a Flexcut Whittlin Jack with sheath. I’ve only used the knife for a few hours roughing out some pieces. Aside from that I’ve worn the sheath with knife a few days, both have VERY minimal wear. It could use a good honing, but aside from that is in great shape. Including stock pictures until I can remember to take some. I...

931 days ago

(SOLD) Hirsch bevel edge chisels..... - 4 replies

I bought this set about a year ago, sharpened them, and put them in a tool roll. They are great chisels, but they don’t see a lot of use, so I’ve decided let them go….. The set goes for $99 @ highlandwoodworking. I’m asking $75 shipped to the continental US. http://www.highlandwoodworking.com/hirschbeveledgechisel...

972 days ago

SOLD: Incra TS-LS 32, Incra Miter 5000, Woodpecker's saw gauge - 48 replies

Time to get a great deal for somebody…. This is the final price…... ($465 shipped in the continental 48 states US) Photos can be seen here. I have an Incra TS-LS 32’ model attached to the saw. I have the manuals and all the parts for it. I have an Incra Miter 5000 sled which has been cut to fit my saw. I ...

1178 days ago

Veritas Mk. II Honing Guide and Camber roller - 4 replies

I have a Veritas Mk. II Honing Guide along with the camber roller. Looking to sell. Located in Clinton, MS, but I’m willing to ship for actual cost outside of the lower 48. Guide has been used a bit, and the roller reflects this. Asking $70 for the set. PM me if interested, I will respond in the order I receive them…..

1400 days ago

Ridgid granite top table saw R4511 for sale - 3 replies

As much as I don’t want to, I’m selling my R4511. I have a picture of it in one of my projects. The saw with the original equipment is for sale, but I’m keeping the Incra… I’ve posted the saw on craigslist, but the price is negotiable…. http://jackson.craigslist.org/tls/1977546649.html PM me if inte...

1411 days ago

Happy 5th Anniversary, a reason to go to the shop - 11 replies

My wife and I celebrate our fifth anniversary today. I don’t think that’s as big of an accomplishment at 50 years, but it’s a good start by most of today’s standards. I was looking for some information today on the fifth anniversary and found this…. http://marriage.about.com/od/5thweddinganniversary/p/5anniv.ht...

1450 days ago

Would you sell a Ridgid R4511? - 20 replies

I have an R4511 and love it. I even went to the trouble to get and Incra TS-LS 32, and build a 2’ x 6’ mobile base for it. I have a router extension, and a storage extension also. The problem I have is that the whole setup weighs too much. It has made the floor in the center of my shop sag from the weight. I went to the troub...

1471 days ago

Random Hand planes - 8 replies

I have several random hand planes to get rid of. I won some lots on ebay a few weeks ago. I got what I wanted, now it’s time to sell the rest. I think there are two Stanley handymans, a Dunlap, a Craftsman or two and some Millers Falls economy planes. Asking $5-$15 for each +shipping. PM me if interested and I can email some pictures....

1486 days ago

The Great, "Almost Got It" thread. - 17 replies

So, let me say here, that I’m sure there are other threads like this out there, but I wanted to vent… I know all of us have had a time when one of these three things happens to us….. 1. We buy a tool that we can’t live without at full price. Then, a month later (just out of the stores price match policy) the price d...

1487 days ago

Plywood bench top thoughts... - 2 replies

Ok, so I have a bench with a top made of HD plywood. I have two sheets of this screwed together. The bench does ok, but I want more precision. With this in mind, I should mention that I got about six 3’x5’ sheets of unfinished, 5-ply, “void free” red and white oak plywood. I believe the 2nd and 4th layers of this wood...

1488 days ago

Did I get a deal on these planes (and tools) ? - 4 replies

Ok all you Galoots, Today I got a Stanley no 95 (type 1) for $35, it is missing the nickel cap adjustment screw. I also got a Stanley 7C (type 15) for $50. It appears to have been well used and taken care of, probably 90-95 percent jappaning. I also got a Stanley 6 (type 14) in a fully loaded carpenter’s toolbox for $35, the tote is bro...

1748 days ago

Powrkraft Radial Arm Saw..... - 6 replies

I have an old Powrkraft Radial Arm Saw that I would like to get rid of. I bought it off Craigslist about two months ago. Since then I’ve put a new mdf adjustable table on it, and regreased the motor (runs like new). THERE IS NOTHING WRONG WITH THE SAW, the problem is that I really don’t have room for it in my small shop. Since I...


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase