LumberJocks

JamesVavra's Favorites

  • Advertise with us
View Sam Shakouri's profile

A PROJECT IN PROCESS

12-14-2012 03:02 PM by Sam Shakouri | 16 comments »

I would call this project ” From Flat Blank ( 25mm thick ) To 100 mm Deep Bowl”. It maybe ready early next year as I am very busy at the moment. I had some rough idea about it but I decided to try it for the first time. It can be segmented or made of one solid piece of timber of your choice, also, it can be round or square. Here, I am going to show you the first steps befor geting it ready for the lathe to finish it.For that, I made a plywood tool r...

Read this entry »


View Filinvested's profile

Scraps to Beads

10-16-2010 01:13 PM by Filinvested | 20 comments »

I’ll try to explain how I did this project:http://lumberjocks.com/projects/38288 1. I take a cutoffs, which just can’t to waste 2. Cut them into small pieces, not necessarily cubic: 3. Disks we need: 40, 120, 320 sand paper and wool disk 4. A tin and PVC stripes for soundproofing: 5. My driil. It can work for hours at speed ‘C/D’ (i have been told it could be problem for drills). 6. An IKEA stool and milled groove in it for the tin. 7. The...

Read this entry »


View mafe's profile

The 30 minutes MaFe chisel plane - blog.

05-28-2011 03:14 PM by mafe | 35 comments »

The 30 minutes MaFe chisel plane.It gets short for all of us one day… I have seen plenty of different versions of the so called ‘chisel plane’, and all had the same problem for me – they simply took too long, and was too complex to make compared to then just making a real hand plane right off. Why make a chisel plane?1. I can’t afford different – that is a good idea then to make one.2. I have a hand plane but could use a ‘plane’ for cleaning up ...

Read this entry »


View McLeanVA's profile

Cutting Board: How To's #1: Zig Zag Cutting Board - How To:

10-04-2010 11:38 PM by McLeanVA | 51 comments »

For those of you who asked me for a tutorial on how to make the zig zag legless vegetable death table (cutting board), here is my best shot. I am far too impatient to take photos when I work, so I decided to illustrate the process using some good old Adobe PhotoShop. I hope you find this useful and informative. I will outline the process in 10 steps below. I have assumed that when viewing these steps that basic woodworking skills are familiar to you. If you have questions, or run into snag...

Read this entry »


View mafe's profile

MaFeBurnisher (scraper set up tool) Blog updated 4oct2010

10-04-2010 12:42 AM by mafe | 28 comments »

MaFeBurnisher BLOGscraper set up tool Ok I posted the project, and here are the blog, since there seems to be some wishes for that now… If there are wishes, I’ll make a work drawing with measures, but I think it’s quite ‘out the road’.(And thank you, I’m better today, so I could spend a little quality time in the work shop 2×40 min.). The project comes from different ideas I have seen around, and the fact I’m not all happy for my VERITAS...

Read this entry »


View newTim's profile

Secrets of the String Box Revealed #2: Laminate The Strings

08-26-2010 07:42 AM by newTim | 6 comments »

I’ve prepped over thirty pictures so far so I tried to break them up into logical groups. The first part is to laminate the strings. For this box I’m using the re-saw technique and start with a thick piece of wenge (8/4) milled flat and square. I re-sawed some strips of maple and ran them through the drum sander for thickness and to remove any larger saw marks. I made a single rip cut on the wenge with a gentle random curve on the bandsaw and glued a thin strip of maple in bet...

Read this entry »


View ~Julie~'s profile

Workshop Build #24: Wall - Mounted Bins

08-18-2010 04:44 PM by ~Julie~ | 11 comments »

I posted a question in the forum section here two months ago asking what others did for organizing all their screws, hooks, etc. in their shops. Some people suggested buying plastic bins, others said use jars or bags. I had a plan in a magazine full of shop storage and tool cabinets put out by the Woodsmith/Shop Notes people and so I decided to make my own. Unfortunately I felt like one of Santa’s elves with the assembly line of parts. It seemed to take forever to make all the b...

Read this entry »


View degoose's profile

How to make a endgrain tumbling block butcher block board!

08-12-2009 12:13 PM by degoose | 50 comments »

Hi guys ,, I had a request to make a tutorial with regards the endgrain Tumbling Block Design.First off,.., You need to decide the size of the blocks…. for this example I used 1” stock… Or something similar.. actually just over .. once dressed. Set the blade of the table saw to 60 degrees.. a bevel box makes this simpleI use the INCRA fence system so it is easy to rip bevels off side of the blade.Once the bevels are ripped measure the length of the bevel and move the f...

Read this entry »


View poroskywood's profile

Drunken Cutting Boards #2: Smooth Flowing Drunken Checker board

09-21-2009 03:49 AM by poroskywood | 15 comments »

So having read part #1 I’ll complete the second variation of the Drunken checker board pattern. The process is basically the same except for one critical part and is as follows. Start again by taping two blanks together. This time In stead of making opposing S cuts I’ll follow the S pattern with each cut. (I get a little sloppy, but it works out OK). Follow the Part #1 procedure. CRITICAL PART! This step creates the difference between the pattern in part one ...

Read this entry »


View davidroberts's profile

Fold Down Outfeed Table

10-11-2009 06:22 AM by davidroberts | 9 comments »

I built this fold down outfeed talbe about two years ago and it still going strong. I give the design credit to Jim Becker at http://sawsndust.com/p-outfeed.htm He provides a plan sheet on his website. I did modify his design a bit to suite my needs. This is what I had in mind when I started to think about the project. I just happened upon Jim’s site, and I’m glad I did. He attached the OFT using 45 degree supports attached to the back of his TS, to eliminate those pesk...

Read this entry »


1 2 next »
17 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase