LumberJocks

Saving A Jet JWP-15CS From Dump #8: 24hour results of EvapoRust and table, "hack" paint job

  • Advertise with us
Blog entry by Holbs posted 04-06-2015 02:36 AM 1779 reads 0 times favorited 6 comments Add to Favorites Watch
« Part 7: Washed base, panels. Motor rust concern. Bolts & Nuts Part 8 of Saving A Jet JWP-15CS From Dump series Part 9: Lower table ROS'd, mineral spirited, paste waxed. Also, about to tackle gummy rusty columns »

Good results from EvapoRust (yet, once again!). Here, the table is 5 minutes removed from my makeshift lower planer table holding jig (sheet metal and evaporust) and after a gentle washing. Have to ROS sand this week and research cleaning and protecting cast iron table tops (has been a while since doing my jointer beds). Table is not in bad shape at all, except for a dime size area of severe pitting, which I guess stays forever?

And my shhhhhh don’t look closely hack paint job:

-- The Carpenter Bee is derived from the Ancient Greek word wood-cutter



6 comments so far

View Roger's profile

Roger

20431 posts in 2381 days


#1 posted 04-06-2015 01:24 PM

Wow! You are gettin er done. Keep on keepin on.

-- Roger from KY. Work/Play/Travel Safe. Keep your dust collector fed. Kentuk55@yahoo.com

View gfadvm's profile

gfadvm

14940 posts in 2267 days


#2 posted 04-06-2015 02:50 PM

Looking good! The paint job looks fine from here. Just ROS that cast iron (120-180 grit) and keep it waxed and you will have a smooth, slick surface that will not rust.

-- " I'll try to be nicer, if you'll try to be smarter" gfadvm

View JoeinGa's profile

JoeinGa

7654 posts in 1584 days


#3 posted 04-06-2015 04:17 PM

You could give those panels a light sanding and paint the whole thing. Then you wont have those splotchy areas that dont quite match.

-- Perform A Random Act Of Kindness Today ... Pay It Forward

View Holbs's profile

Holbs

1471 posts in 1606 days


#4 posted 04-06-2015 06:40 PM

I’ll live with the hack paint job, Joe. But will ask around about sand blasting this week. I still have that option until I start putting everything back together. I’m a telephone man (somewhat like AT&T techs you see driving around) so know alot of customers with blasting equip. I’ll have to ask a favor or small fee to blast all pieces. I’m sure, I can primer & paint myself (well, with my dinky Summit HVLP). But if sand blasting does not get done, I’ll survive with the panel pieces as is.

-- The Carpenter Bee is derived from the Ancient Greek word wood-cutter

View MerylL's profile

MerylL

57 posts in 948 days


#5 posted 12-18-2016 03:56 AM

Do you remember how you removed those 2 rollers from the bottom bed? I can only think that the ends are pressed on them because there is no threaded fasteners. Today I removed my set screws, but it affected nothing other than the eccentric shaft spun. So it makes me think that the rods were placed in and the ends then pressed into the bearings, which stay in the roller. I cleaned them in place but it really has me curious!

View Holbs's profile

Holbs

1471 posts in 1606 days


#6 posted 12-18-2016 04:09 AM

I do not remember, at this time. It was logical once I had the table in hand. Didn’t even had the parts diagram PDF when it came time to disassemble. Used the PDF excessively upon reassembly.

-- The Carpenter Bee is derived from the Ancient Greek word wood-cutter

Have your say...

You must be signed in to post the comments.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com