LumberJocks

How I built the Timber frame Staircase

  • Advertise with us
Blog entry by BenhamDesign posted 12-11-2017 05:13 PM 904 reads 0 times favorited 0 comments Add to Favorites Watch

You can watch it be built on YouTube Or read about it below

I built this timber frame staircase from reclaimed beams that came from another client’s house a few miles up the road. The beams use to support a pergola, that was torn down during their remodel.

We templated the area where the stairs where going to go and brought it back to the shop and premade them. The install was fairly straightforward as they were already in assembled in sections. All that was left was to put them in place and bolt them in.

The through tenons with the wedges were of course, as much of my work. Inspired by traditional Japanese joinery techniques.

A recount of the video

If you would like to watch the voice over version of this video please join me on Patreon

The reclaimed beams have already been milled and sanded to thickness. I Start out by cutting them to length on the table saw.

Since the blade is at full height, for safety, I use my knee to shut down the saw as soon as the cut is complete before moving the workpiece.

This material is just a little bit too thick for my saw to cut all the way through so I use my Japanese pull saw to finish the cut.

And since the cut wasn’t perfectly flush I use a pattern bit in my router to flush it up.

I am working with soft Douglas FIr, it is prone to splintering so I severed the grain with a knife to keep a clean shoulder.

Then cut the shoulder of the tenon to depth with my router.

Once I established the shoulder, I switched to a more aggressive bit and hogged off the rest of the material. This method left a lot of tool marks on the tenon, which normally wouldn’t be a problem, but these tenons are going to be functional and decorative so I came back with a hand plane and cleaned them up.

Now I set up the fence on the band saw to rip the tenons to width and used my Japanese pull saw to trim off the excess. I used the same knife scoring technique to prevent tear out.

To be sure the shoulders seated tightly to the stringers I took a few minutes to finesse the shoulder cleaning up anything that wasn’t square to the face.

I laid out the rise and run of the stair treads and marked out for the through mortises and headed over to the drill press to hog out most of the material with a forstner bit.

I took my time to make a plywood template that fit perfectly over the tenons so I could use my router to quickly clean out the rest of the material. I came back with a chisel to square up the corners, and finish chopping through to the other side of the mortise since my router bit was not long enough to cut all the way through.

All those scrap pieces I cut off from the tenons; I was able to rip down and use to create the wedges that would hold it all together.

To create the wedges, I set up a stop block on the band saw so I could quickly cut the decorative notch, and then came back with a wedge against the fence to cut a matching taper to complete the shape.

I did a little cleanup on the spindle sander to refine the shape and then built a plywood jig so I could quickly mark out the location for the wedges on all 15 steps.

To prevent tear out I used a chisel to stake out the perimeter of the mortise for the wedges, came back with a drill to remove the bulk of the material and routed out the perimeter.

Once I established the basic shape of the mortise, I came back with a chisel and chopped out the rest of the material to match the taper of the wedge.

From here on out it was a lot of finessing the fit. Driving the treads in, testing the fit, driving the tread out, and relieving some material with chisels and hand planes. So on and so forth until they all fit snugly.

If you enjoyed reading this blog post, and want more Join me on My Blog

Or my Custom Furniture Website

-- What I do in and out of the shop at http://www.BriansBenham.com



0 comments so far

Have your say...

You must be signed in to post the comments.

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com